Publicidad
Operating Instructions
Technical Support
Please call our Tool Hotline at 1-800-
543-6400 with any questions regarding
the operation or repair of this tool or
for additional copies of this manual.
Fastener And Replacement
Parts
Use only
WARNING
!
genuine Campbell
Hausfeld 18 gauge fasteners (or equiva-
lent - see Fastener Interchange
Fasteners
The following Campbell Hausfeld staples are available at local retail stores. If you need help locating any item, call customer
service at 1-800-543-6400. Campbell Hausfeld staples meet or exceed ASTM Standard F1667.
Model #
Length
FN158K00
1/2"
FN168K00
5/8"
FN208K00
3/4"
FN258K00
1"
Interchange Information
Staples used in the Campbell Hausfeld SN258K Finishing Stapler will also work in: Senco LN4450, SJS-LR, SKS L11-15,
Hitachi N3804A, Duofast BN-1832S, KN-1848, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100.
Troubleshooting Guide
Stop using stapler immediately if any of the following problems occur. Serious personal injury
WARNING
!
could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized
Service Center.
Problem
Air leaking at trigger valve
area.
Air leaking between housing
and nose.
Air leaking between housing
and cap.
Stapler skips driving staple.
Information). Tool performance, safety
and durability could be reduced if
improper fasteners are used. When
ordering replacement parts or fasten-
ers, specify by part number.
Tool Repair
Only qualified personnel should repair
the tool, and they should use genuine
Campbell Hausfeld replacement parts
and accessories, or parts and accessories
which perform equivalently.
Wire
Crown
Diameter
Size
18 Gauge
1/4"
18 Gauge
1/4"
18 Gauge
1/4"
18 Gauge
1/4"
Cause
O-rings in trigger valve housing are damaged
Loose screws in housing
Damaged o-rings
Damage to bumper
Loose screws
Damaged gasket
Worn bumper
Dirt in nose piece
Dirt or damage prevent staples or pusher from
moving freely in magazine
Damaged pusher spring
Inadequate air flow to stapler
Worn o-ring on piston or lack of lubrication
Damaged o-ring on trigger valve
Air leaks
Cap gasket leaking
Point
Finish
Chisel
Galvanized/Vinyl Coated
Chisel
Galvanized/Vinyl Coated
Chisel
Galvanized/Vinyl Coated
Chisel
Galvanized/Vinyl Coated
5
Model SN258K
Assembly Procedure For
Seals
When repairing a stapler, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots. After
reassembling, a few drops of 30W
non-detergent oil or equivalent, must
be added through the air line before
testing.
Staples
Collation
Per Stick
Adhesive
100
Adhesive
100
Adhesive
100
Adhesive
100
Solution
Replace o-rings and check operation of
Work Contact Element (WCE)
Tighten screws
Replace o-rings
Replace bumper
Tighten screws
Replace gasket
Replace bumper
Clean drive channel
Clean magazine
Replace spring
Check fitting, hose, or compressor
Replace and lubricate o-rings
Replace o-rings
Tighten screws and fittings
Replace gasket
www.chpower.com
Staples
Per Box
5000
5000
5000
5000
Publicidad
Solución de problemas
