Taurus Geyser Diamond 2400 Manual De Usario página 17

Steam blast:
- This function proportions extra steam for eliminating
wrinkles.
- Press the steam blast button (B). Wait a few seconds
until vapour penetrates the fibres of the garment before
pushing the button again. For optimum steam quality, do
not apply more than three successive blasts.
- The spray button has to be pressed repeatedly to release
the first spray.
Vertical steaming
It is possible to iron hanging curtains, items of clothing
on his hanger, etc. To do so, follow the instructions:
- Select the maximum temperature of the iron, while tur-
ning the temperature regulator of the iron in a clockwise
direction.(Fig 2)
- Move the iron in a top to bottom direction while pres-
sing the steam control ( B ). Important: for cotton and
linen, its recommended to put the iron base in contact
with the material. For other more delicated fibres, it's
recommended to keep the iron base at some centimetres
of distance.
Auto-off function: *
- For energy-saving purposes, the appliance goes to auto-
off status if it is not moved for a pre-determined time
period. When this happens, an audible warning is heard
and the auto-off indicator lamp (G) flashes, indicating
that the function is active.
- Auto-off in horizontal position: after approximately 30
seconds without moving the appliance.
- Auto-off in vertical position: after approximately 8
minutes without moving the appliance.
- To return to normal functioning, simply move the
appliance again.
(*) Only available in model Geyser Titanium 2600
Once you have finished using the appliance:
- Select the minimum position (MIN) using the thermos-
tat control.
- Unplug the appliance to the mains.
- Remove the water from the water tank.
- Clean the appliance
Cleaning
Disconnect the appliance from the mains and let it cool
before undertaking any cleaning task.
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning the
appliance.
- Do not submerge the appliance in water or any other
liquid, or place it under a running tap.
Self-cleaning function:
- It is important to self-clean the appliance at least once
a month to remove calcium and any other built-up mine-
rals inside the iron.
Manual Geysers.indb 17
- Fill the depository to its maximum level, as indicated on
"water fill" section.
- Place the iron in a vertical position, plug in to the mains
m and select the maximum temperature.
- Leave the appliance to heat up until the pilot light indi-
cates that it has reached its consigned temperature.
- Unplug the appliance and place in the sink.
- Press the self-clean button, and keep it pressed down.
- Let the water flow out through the steam vents in the
base, while lightly shaking the appliance.
- Release the button after a minute or when the tank
becomes empty.
- Leave the iron in the vertical position until it has
cooled.
Anomalies and repair
- Take the appliance to an authorised technical support
service if problems arise. Do not try to dismantle or repair
without assistance, as this may be dangerous.
- If the connection to the mains has been damaged, it
must be replaced and you should proceed as you would
in the case of damage.
For EU product versions and/or in case that it is reques-
ted in your country:
Ecology and recyclability of the product
- The materials of which the packaging of this appliance
consists are included in a collection, classification and
recycling system. Should you wish to dispose of them,
use the appropriate public recycling bins for each type of
material.
The product does not contain concentrations of substan-
ces that could be considered harmful to the environment
This symbol means that in case you wish to
dispose of the product once its working life has
ended, take it to an authorised waste agent for
the selective collection of waste electrical and
electronic equipment (WEEE)
This symbol indicates that the surface may heat
up during use.
This appliance complies with Directive 2006/95/EC on
Low Voltage and Directive 2004/108/EC on Electromag-
netic Compatibility.
26/06/12 16:17