Intercom; Pairing Two Helmets; Cellphone - Uvex boss 525 bt Instrucciones De Uso

2.3 INTERCOM

2.3.1 Pairing two helmets

To pair two helmets, fi rst decide which is to be the Master helmet and which the
Slave.
1 – The helmets must be turned off and close together (1-3 metres).
2 – Press the "HELMET" button on each helmet continuously for around 7 seconds
(the pairing command) until the LED begins to fl ash rapidly and the helmet emits a
high tone.
Attention: the LED lights up and the "HELMET" emits a tone after 4 seconds -
this indicates the helmet is switched on. Keep the button pressed to reach pairing
mode, indicated by the LED fl ashing rapidly and a tone sounding in the headset.
3- Briefl y press the multifunction "HELMET" button on the Master helmet. This will
cause the Master to seek the Slave to pair with.
After around 5 seconds both helmets will emit a high tone and both LEDs will switch
from a fast to a slow fl ash. This indicates that the helmets are paired and the intercom
function is ready to use.
If the steps for the pairing process are completed but the helmets are still not
connected, this will be indicated by a low tone which indicates pairing failure. Switch
off both helmets and repeat the pairing operation from the beginning.
Attention: the connection between two paired helmets will fail if the distance
between them exceeds 10 metres. To reconnect, bring them closer together and
press the "HELMET" button on one of the helmets for 2 seconds unitl a tone
sounds in the headset.
If other Bluetooth® devices are switched on the vicinity of the helmets this will not
prevent connection between the two helmets, but may slow it down.
Attention: if you try to pair one helmet only the system will not indicate an error
but after 40 seconds will return to normal operation.
2.3.2 Use as Intercom
The Slave helmet must be switched on fi rst, then the Master.
As soon as it is switched on, the Master helmet seeks the Slave and connects
28
ENGLISH
automatically. The helmets are then ready to communicate with each other, and if a
paired cellphone is also on they are also able to receive cellphone calls.
If the two helmets cannot connect (low headset tone), switch off and repeat the
operation. Two helmets that are switched on and paired can be connected to each
other at any time with a medium press of the "HELMET" on either the Master or Slave
helmet. To disconnect two paired helmets use a medium press of the "HELMET"
button until you hear a high tone in the headset.
Note: the helmets can also be used in intercom mode when connected to their
respective cellphones or when one of the helmets is connected to the GPS. When
the cellphone call or GPS message is received the intercom will disconnect and
reconnect automatically when the phone call or GPS message is complete.
Note: the intercom cannot be used while listening to music on an MP3 player.

2.4 CELLPHONE

2.4.1 Connecting a Bluetooth® cellphone to the UVEX BLUETOOTH system
Consult the section describing connection of Bluetooth® devices in your Bluetooth®
cellphone handbook to check the connection procedure, as it is different for every
cellphone. Then pair the cellphone and helmet by using your cellphone, which ""sees"
your helmet simply as a Bluetooth® headset.
1 – The helmet must be switched off.
2 – Press the "HELMET" button on the helmet for about 7 seconds (pairing press)
until the LED fl ashes rapidly and the high tone emitted by the system indicates that
pairing has been accepted.
Note: the LED lights up and the helmet emits a tone after 4 seconds. This indicates
the helmet is on. Maintain pressure on the button to complete pairing, identifi ed
by the LED fl ashing rapidly and the headset tone.
3 - Begin the Bluetooth device pairing procedure on your cellephone. Carry out the
procedure within 40 seconds of the helmet reaching pairing mode (LED fl ashes rapidly).
4 – The name STILO BT x.x xx will appear on the cellphone display in the list of
available devices.
29
ENGLISH