Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

Enlaces rápidos

Aegis
Quick Start Guide
First-Time Use / Admin Mode Setup
NOTE: if you are using the Aegis Configurator (sold separately) to
set up your Padlock DT, first ensure that the device to be configured
CONFIGURABLE
has the "configurable" logo on the belly label. Also, DO NOT perform the
following Manual Admin and USER PIN SETUP steps below; The Aegis Configurator will only
recognize devices in their factory "out of box" state or devices that have been completely reset.
1.
To access the Aegis Padlock DT connect the drive to a power outlet via the AC Adapter
and a USB port using the USB 3.0 cable (this cable is also compatible with USB 2.0).
2.
Once connected turn the power switch on the back of the drive to the ON position.
3.
The unit will do a self-test to verify all security components are working properly. The LEDs
will go through 3 test stages RED, GREEN, and BLUE. This will be followed by three
GREEN
flashes on a successful test. Any test failure will leave the unit in an interoperable
state with the
RED
4.
Once the self test is successfully completed, the LED will display Solid
GREEN
to indicate the Padlock is waiting for a PIN to be set.
Press + 9. The LED will change to Solid
5.
6.
Enter the new Admin PIN and press
short blinks, then return to Solid
7.
Re-enter the Admin PIN and press the
3 seconds.
8.
LED will then turn
pressed, will return the drive to a standby state.
9.
The Admin PIN is now set and will allow access to the drive or the Admin features.
10. To UNLOCK the drive, exit Admin by pressing the
press .
Padlock
LED flashing.
BLUE
BLUE
and remain in Admin mode for 30 seconds or if the
DT FIPS
BLUE
and Blinking GREEN.
key. If accepted the
and Blinking GREEN.
key. If accepted the
button. Then enter the new PIN and
PIN Requirements
PINs must be a minimum length of 7 digits
with a maximum of 16 digits.
Cannot contain all consecutive numbers
(2345678 or 9876543)
Cannot contain all same number (1111111)
1
Cancel button
2
UNLOCK button
LED Indicator light
3
Remember to save your password in a safe place.
If lost or forgotten, there is no way to access the drive.
If you are having difficulty please refer to the complete
user's manual which is loaded on your Aegis Padlock
drive and is also available at www.apricorn.com
BLUE
and Solid
GREEN
LED will flash for 3
GREEN
LED will be Solid for
key is

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Aegis Padlock DT FIPS

  • Página 1 “out of box” state or devices that have been completely reset. To access the Aegis Padlock DT connect the drive to a power outlet via the AC Adapter and a USB port using the USB 3.0 cable (this cable is also compatible with USB 2.0).
  • Página 2 The button can also be used to exit out of the Admin mode. Note: The Aegis Secure Key will not be recognized by any operating system in its locked state. Unlocking the Drive To unlock the drive, enter either a User PIN or Admin PIN and press the UNLOCK button.
  • Página 3: Requisitos De Pin

    Aegis únicamente puede reconocer Productos Seguros Aegis en su Modo Inicial. 1. Para acceder al Aegis Padlock DT, conecte la unidad a una toma de corriente a través del adaptador de CA y un puerto USB con el cable USB 3.0 (este cable también es compatible con USB 2.0).
  • Página 4: Bloqueo Del Padlock Dt Flips

    PIN de usuario se agregó correctamente. Formato para Mac OS La Aegis Padlock DT viene preformateada en NTFS para Windows ® y está lista para su uso. Para Mac OS, primero debe formatear la unidad a un sistema de archivos compatible con Mac.
  • Página 5 «configurable» sur l’étiquette du ventre. Si vous utilisez le con gurateur pour installer vos produits sécurisés Aegis, NE suivez PAS les étapes ci-dessous ; les produits sécurisés Aegis peuvent être reconnus par l’Aegis Con gurator uniquement en Mode prêt à l’emploi.
  • Página 6 Pour verrouiller le lecteur, appuyez simplement sur le bouton . En cas de succès, le voyant ROUGE sera allumé en continu. Si une écriture de données est en cours sur le produit Aegis Padlock DT, le mode verrouillé sera reporté jusqu’à la fin de l’opération.
  • Página 7 Schritte durch; der Aegis Con gurator kann nur Aegis Secure-Produkte im Out-of-Box-Modus erkennen. Um auf das Aegis Padlock DT zuzugreifen, schließen Sie das Laufwerk über das Netzteil und einen USB- Anschluss mit dem USB 3.0-Kabel an eine Steckdose an (dieses Kabel ist auch mit USB 2.0 kompatibel).
  • Página 8 Administratormodus zurückgekehrt ist. Formatierung für Mac OS Der Aegis Padlock DT ist in NTFS für Windows ® vorformatiert und kann sofort verwendet werden. Unter Mac OS müssen Sie zuerst das Laufwerk auf ein Mac-kompatibles Dateisystem umformatieren. Sobald das Laufwerk entsperrt und in einen USB-Anschluss eingesteckt ist, öffnen Sie die Mac-Festplatten-Dienstprogramm unter Programme / Dienstprogramme / Festplatten- Dienstprogramme und führen Sie folgende Schritte aus:...
  • Página 9: Guida Rapida

    “configurabile” sull’etichetta del ventre. In caso di utilizzo del Con guratore per impostare un prodotto Aegis Secure, NON eseguire i passaggi di seguito: il Con guratore Aegis è in grado di riconoscere soltanto i prodotti Aegis Secure in modalità Out- of-Box.
  • Página 10 PIN utente è stato aggiunto correttamente. Formattazione per Mac OS Aegis Padlock DT viene preformattato in NTFS per Windows ® ed è pronto per l’uso. Per Mac OS, è necessario prima riformattare l’unità su un file system compatibile con Mac.

Tabla de contenido