Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
AUDIO SIGNAL CABLES
When installing the audio cables between the RCA outputs of the head unit and the RCA inputs of the amplifier
[ 6 ], the audio and power supply cables should, if possible, not be routed along the same side of the vehicle.
We recommend a separated installation, e.g. routing the power cable through the cable channel on the left side
and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents
interferences due to crosstalk into the audio signal.
PHASE
LOW
PASS
POWER
180°
0°
50Hz 150Hz
PROTECTION
OFF
GP600
ON
AUTO TURN ON
ACTIVE SUBWOOFER SYSTEM
HIGH LEVEL INPUTS & AUTO TURN ON
The high level inputs under HI LEVEL INPUT [ 7 ] is suitable to connect the device input with speaker wires, if
your head unit is not equipped with pre-amplifier RCA outputs. Extend therefor every regarding speaker cable
from your head unit with appropriate speaker cables from your car audio retailer to the mounting location of
the amplifier. Then connect the each matching loudspeaker cable with the cables of the included High Level
Input jack.
CAUTION: Never use the high level inputs and the RCA inputs at the same time. This may damage the
device seriously. Use the enclosed cable plug to connect each terminal.
PHASE
POWER
180°
0°
PROTECTION
OFF
AUTO TURN ON
ON
AUTO TURN ON
Push the AUTO TURN ON switch [ 8 ] to ON position. The amplifier detects now a voltage rise (6 Volts) over
the connected input signal on the HI LEVEL INPUT [ 7 ] when the head unit will be switched on. Hence, the
amplifier will also be turned on. As soon as the head unit will be turned off, the amplifier turns also automatically
off. In this case the turn-on connection [ 5 ] is not needed.
NOTE: The AUTO TURN ON function usually works with 90% of all head units, because they are equipped
with "High Power"-outputs. Only with a few older and still existing head units the Auto Turn On function is not
working.
INPUT SENSITIVITY
Turn the LEVEL INPUT [ 9 ] controller of the amplifier to the MIN position. Then turn the volume controller of
the head unit to 80 - 90% of its full setting. Now turn LEVEL INPUT [ 9 ] clockwise until you hear some distor-
tion. Then turn back LEVEL INPUT [ 9 ] slightly until you hear a cleaner sound.
POWER
PROTECTION
AUTO TURN ON
REMOTE
BASS
LEVEL
BOOST
INPUT
6
0dB
12dB
MIN
MAX
LOW
BASS
LEVEL
PASS
BOOST
INPUT
7
50Hz 150Hz
0dB
12dB
MIN
MAX
GP600
ACTIVE SUBWOOFER SYSTEM
8
PROTECTION
PHASE
LOW
BASS
PASS
BOOST
9
180°
0°
50Hz 150Hz
0dB
OFF
GP600
ON
ACTIVE SUBWOOFER SYSTEM
LOW LEVEL
INPUT
HI LEVEL INPUT
R
L+
L–
L
R+
R–
FUSE
LOW LEVEL
INPUT
REMOTE
HI LEVEL INPUT
white
L+
L–
black/white
grey
R+
R–
grey/black
PHASE
LOW
PASS
POWER
180°
0°
50Hz 150Hz
OFF
GP600
ON
AUTO TURN ON
ACTIVE SUBWOOFER SYSTEM
REMOTE
LEVEL
INPUT
12dB
MIN
MAX
POWER
GND
REM
+12V
POWER
= L +
R
= L –
= R +
L
= R –
FUSE
BASS
LEVEL
BOOST
INPUT
0dB
12dB
MIN
MAX
LOW LEVEL
INPUT
HI LEVEL INPUT
L+
L–
R+
R–
GND
REM
+12V
REMOTE
HI LEVEL INPUT
L+
L–
R+
R–
R
L
FUSE
9
LOW LEVEL
INPUT
R
L
POWER
Publicidad
Tabla de contenido
