Multiplex MULTIcont BL-25 FLEXX Manual De Instrucciones página 3

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

! These operating instructions are an integral part of this
product. They contain important information and safety
notes, and should therefore be kept in a safe place at all
times. Be sure to pass them on to the new owner if you ever
dispose of the product.
1. S
N
AFETY
OTES
! Read the instructions before using the controller
! Avoid heat build-up
Provide unobstructed air circulation round the controller
! Do not connect the flight battery with reversed polarity
Connecting the battery leads with reversed polarity will in-
stantly wreck the controller
For this reason:
• red wire to the POSITIVE terminal (+)
• black wire to the NEGATIVE terminal (-)
! When soldering or working on the motor or controller
Always disconnect the battery (short-circuit / injury hazard)
! When testing and running the power system
Do not run the motor while holding it in your hand; always se-
cure the model firmly.
2. S
PECIFICATION
MULTIcont
Order No.:
Max. continuous current.:
Receiver power supply
(BEC):
Clock frequency:
Signal:
Deadband:
Timing:
Cut-off voltage:
BEC voltage:
BEC current:
Dimensions in mm (approx.):
Weight incl. cables:
Maximum servo count for MULTIcont BL-25 FLEXX speed
controllers in BEC mode**
MULTIcont
Maximum number of micro / standard servos*:
Maximum number of high-torque servos:
* MULTIPLEX Nano-S or Tiny-S servo types.
** If the number of servos in the model exceeds the stated
maximum, it is essential to disable the BEC system and use a
separate receiver battery ( 6.).
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating instructions for MULTIcont
BL-25 FLEXX brushless speed controllers
BL-25 FLEXX
# 7 2240
25 A
max. 3S LiPo oder
10 Zellen NiXX
8 kHz
Neutral: 1.5 ms
Max. speed: 1.9 ms
Max. reverse: 0.9 ms
4 %
Auto
LiPo = 3.2 V / cell
NiXX = 50% of U0
6,0 V
max. 1,0 A
38 x 27 x 23
38 g
BL-25 FLEXX
2
1
3. S
F
PECIAL
EATURES
MULTIPLEX MULTIcont BL-25 FLEXX speed controllers include
interesting features:
Direction of rotation: forward, brake and reverse
Fixed signal values: no calibration required
On / Off switch
Safety start system prevents motor starting accidentally when
battery is connected
Motor cut-off if serious radio interference occurs, or trans-
mitter signal fails
Temperature guard: if the controller overheats, it reduces
power to the motor.
! Caution: The BL-25 FLEXX
cannot be programmed with the MULTImate or PC!
4. W
IRING
! Note: when fitting your preferred plug / socket system in
order to connect the MULTIcont BL-25 FLEXX speed
controller to your motor and / or battery, please observe the
following points:
Soldering requires some care, as the quality of the joints is cru-
cial to the reliability of the power system:
Use electronic-grade solder for all soldered joints
Do not use acid-based solder flux
Parts to be soldered must be hot enough (the solder must
flow), but must not be overheated (damage to components)
If you are unsure, ask a modeller with experience in soldering
to help you
Carefully insulate all solder joints and bare wires (e.g. using
heat-shrink sleeving)
Attaching the battery connectors
The battery connectors have to be attached to the two wires (red
= +, black = -). Keep the wires as short as possible. If necessary,
cut the battery leads to the required length. Fit a piece of heat-
shrink sleeve on each wire, and shrink the sleeve over the
soldered joint.
Take great care to maintain correct polarity when soldering the
battery connectors to the leads. Reversed polarity inevitably and
invariably wrecks the controller.
Connecting the speed controller to the motor
The motor is connected to the three wires which exit one end of
the controller. Solder sockets to the wires which match the motor
connectors, and insulate each soldered joint with a separate
heat-shrink sleeve. Keep the leads as short as possible.
If you need to reverse the direction of rotation of the motor, simp-
ly swap over two of the three wires leading to the motor.
Connecting the three-core lead (UNI connector system) to
the receiver
Connect the three-core receiver lead (attached to the speed con-
troller) to the receiver input socket used for motor speed control:
- With MULTIPLEX RC systems: channel 4 = throttle / motor
- With HiTEC RC systems: channel 3 = throttle / motor
Pin assignment
Negative pin (−)
Positive pin (+)
Signal ( )
Do not connect a separate receiver battery to the receiver,
as the controller supplies current to the receiver and servos
via the BEC circuit. Always keep to the maximum servo
brown
red
orange
Page 1/2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

7 2240

Tabla de contenido