Fellowes AeraMax Pro AM IIIS Manual Del Usuario página 4

DISPLAY PANEL
NOTE: after the unit is turned on the "AQ" light will flash for a few minutes while the system self-calibrates.
1 HEPA FILTER REPLACEMENT INDICATOR –
its status when the access panel is open or closed. If the light is red this indicates the filter
needs replacing. The replacement period will vary depending on the filters used, hours of
use, air quality, and rate of air flow. For filter replacement indicator descriptions see FILTER
REPLACEMENT INDICATORS section.
CARBON FILTER REPLACEMENT INDICATOR –
2
show its status when the access panel is open or closed. If the light is red this indicates
the filter needs replacing. The replacement period will vary depending on the filters used,
hours of use, air quality, and rate of air flow. For filter replacement indicator descriptions
see FILTER REPLACEMENT INDICATORS section.
3 ACCESSORY INDICATOR –
panel is open or closed. This indicator will only be used if an accessory filter is installed in
the unit. If the light is red this indicates the filter needs replacing. The replacement period
will vary depending on the filters used, hours of use, air quality, and rate of air flow. For
filter replacement indicator descriptions see FILTER REPLACEMENT INDICATORS section.
4 AIR QUALITY SENSOR –
panel is open or closed. This indicator monitors the air quality and adjusts the fan speed to
keep your air purified. Blue, amber, and red lights indicate the purity of your air.
OPERATION
The air purifier continuously works in automatic mode; the user can select which preference they would like the purifier to use based on the location or desired operation of the air
purifier. The purifier will operate through a minimized range of speeds, not exceeding the maximum level selected, in order to run quietly while cleaning the room of contaminants.
Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption and extend the life of the filters.
When Auto Mode is selected, the Auto mode indicator will be blue. This mode uses the EnviroSmart ™ technology to monitor the air quality, motion and noise level to adjust the
fan speed in order purify your air as quickly as possible. Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption
and extend the life of the filters.
The machine will continue to use EnviroSmart ™ but only utilizes the 3 lowest, most quiet of the 5 fan speeds.
When Manual Mode is selected, the Manual mode indicator will be blue. This mode allows you to choose one of the 5 fan speeds and keep unit at this speed until Auto Mode is
chosen/selected. EnviroSmart™ sensors will NOT adjust the fan speed in this mode.
SET UP
1. Open unit by pressing the latches on both sides.
2. Remove bag(s) from filter(s) and place back in the unit.
3. Plug the IEC plug into the power cord socket on the back of the unit.
4
1 2 3
This indicator will show
This indicator will
This indicator will show its status when the access
This indicator will show its status when the access
4 5 6
5
PlasmaTRUE™ TECHNOLOGY –
the access panel is open or closed. Creates an ionized field to help safely remove airborne
pollutants. To turn on and off the PlasmaTRUE™ TECHNOLOGY, touch and hold the PLASMA
indicator. A blue light illuminates when the PlasmaTRUE™ TECHNOLOGY is enabled. To disable
the PlasmaTRUE™ TECHNOLOGY, press and hold "Plasma" indicator until light is off.
AUTO MODE –
6
To select, press and hold the button until the icon illuminates. This mode
uses the EnviroSmart ™ technology to monitor the air quality, motion and noise level to adjust the
fan speed in order to purify your air as quickly as possible. This button also includes QUIET MODE.
To select, press and hold until the button turns purple. The machine will continue to use EnviroSmart
™but only utilizes the 3 lowest, most quiet of the 5 fan speeds.
MANUAL MODE –
7
To select, press the button until the icon illuminates. This mode
allows you to choose one of the 5 fan speeds and keep the unit at this speed until AUTO MODE
is chosen again. The internal sensors will not adjust the fan speed in this mode.
8
FAN SPEED INDICATORS –
to clean the room in case of high levels of contaminants. The number of bars illuminated
indicates fan speed.
1 – whisper
2 – low
3 – medium
7 8
This indicator will show its status when
The fan has 5 speeds and can reach turbo speed
4 – high
5 – turbo