Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
48003560 01 Arya IM ML.pdf 1 7/17/2012 10:24:24 AM
CLEANER MAINTENANCE
Emptying the Dust Container
1.
Press the bin release button downward and remove the dust bin from the cleaner.
2.
Hold the container using the bin handle and press the bin emptying latch. The
dustcontainer door will automatically open. [8]
3.
Once empty, gently tap or shake the container to release any excess dust.
IMPORTANT - Do not ll above the max level mark shown on the bin.
Cleaning the w
The clea
wi
performance, reg
dust.
The pre-motor
excessive dust level.
IMPORTANT: All bagless cleaners require regular
rs may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
C
IMPORTANT: Regularly check and maintain th
IMPORTANT: Always ensur
M
Y
To access the Pre-Mot
1. Press the bin release button downward and remove the dust bin from the cleaner.
CM
2.
Rotate the upper section of the bin to remove from the dust container.
MY
3.
Remove t
lter pack.
CY
4.
Gently tap and wash
CMY
excess water and leave to dry fully before re-using. [12]
5.
Reassemble the pre-motor lter pack once fully dry and r
K
Cleaning the dust bin / separation unit
1.
Place the bin o
at surface and remove th
2.
Remove the separation system by lifting from the dust container.
3.
Use a cloth to remove excessive dust from the separation unit surface.
4.
R
the separation unit into the dust bin and r
5.
R
the dust bin to the cleaner.
IMPORTANT - For optimum performance, we recommend that Airvolution system is
inspected after each empty.
AryaManual__1-3_union2.indd 2
ters
aintain optimum cleaning
gainst the side of the bin to release
ld be washed every 5 container empties or when the
ter cleaning. Failure to clean your
lters.
lter pack is fully dry before use.
ter:
[10]
er,
do not use hot water or detergents. [11] Remove
t to the cleaner.
lters.
[13]
lters in position.
Removing a blockage
1.
Check if the dust container is full. If so refer to 'Emptying the dust container' .
[7]
2.
If the dust container is empty but suction is still low:
A.
D
lters need cleaning? If so refer to 'Cleaning the washabl
B.
Check the bin inlet by removing the bin and checking inside the bin inlet.
C.
Check if pre-mot
IMPORTANT - Switch the clean
before checking cleaner.
ter has
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist before
calling your local Hoover service.
•
Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
•
Is the dust container over lled? Please refer to 'Cleaner Maintenance' .
•
ter blocked? Please refer to 'Cleaner Maintenance' .
•
Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically
[9]
reset.
IMPORTANT INFORMATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local Hoover
dealer or direct from Hoover. When ordering parts always quote your model number.
Consumables:
•
P
e r
m
t o
r o
Filter
•
Polisher
Spares:
•
Carpet and Floor Nozzle
•
Hard Floor Nozzle
2
lter is tted and lter door is closed.
and remove the plug from the electricity supply
S106
PO1
G136
G137PC 35601209
(*Certain Models Only)
GB
lters' .
35601198
35600943
35601208
29/03/2011 13.08.33
Publicidad
Tabla de contenido
