ETI Color Preference DL-6-67-907-SV-D Guía De Uso Y Cuidado

Color PreferenCe
noTe: Keep your receipt and these instructions for proof of purchase.
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
noTe: Stick the replacement label on the inner wall of the recessed housing before installation.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
Model # 53805102/Part # DL-4-625-907-SV-D should be installed in 4 in. housings only.
Model # 53804102/Part # DL-6-67-907-SV-D should be installed in 6 in. housings only.
INSTALLATION
Shut off power at the electrical panel before beginning the installation.
1
Remove existing fixture and set aside to recycle in accordance with local requirements.
2
Choose your favorite correlated color temperature (CCT) before installing the fixture housing to the electrical outlet box.
3
noTiCe: The factory setting for the correlated color temperature (CCT) is 2700K, which is the warmest white light. Night light mode
provides reduced light output at 2000K color temperature for very soft illumination at night.
B
Screw the medium base (E26)
4
socket adapter into the socket in
the can.
LIghT DISTrIbuTION
Model # 53805102/Part # DL-4-625-907-SV-D
-/+180
-150 150
-120
0
-90
60
120
180
-60
240
-30 30
300
0
WarninG: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire,
or other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. •
Risk of fire or electric shock. Installation of this LED Retrofit Kit assembly requires a person familiar with the construction and operation of the light fixture's/luminaire's electrical
system and the hazard involved. If not qualified, do not attempt installation. Contact a qualified electrician. • Install this kit only in luminaires (light fixtures) that have the construction
features and dimensions shown in the photographs and/or drawings included in these installation instructions, and where the input rating of the retrofit kit does not exceed the input
rating of the luminaire. • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. • To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other sharp objects.
noTiCe: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
noTiCe: The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be
installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical
installations. • Suitable for type IC or type non-IC installation. • Use only in open luminaires. • Luminaire wiring and electrical parts may be damaged when drilling for installation of LED
retrofit kit. Check for enclosed wiring and components. • This device is not intended for use with emergency exits. • Minimum lamp compartment dimensions for Model # 53804102: 6
inch diameter and 8 inch depth when used in a 6-inch recessed luminaire. • Minimum lamp compartment dimensions for Model # 53805102: 4 inch diameter and 8 inch depth when used
in a 4-inch recessed luminaire.
Use and Care GUide
reCessed led doWnliGHT WiTH niGHTliGHT TriM
®
B
Plug the cable connector on the
5
socket adapter into the fixture.
Model # 53804102/Part # DL-6-67-907-SV-D
-/+180
-150
-120
120
0
-90
90
7 0
1 4 0
-60 2 1 0
60
2 8 0
-30
3 5 0
0
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-eTI-SSLI (1-855-384-7754) www.eTiSSL.com
Model # 53804102
53805102
A
A
6
7
8
150
120
90
60
30
Part # dl-6-67-907-sV-d Certification # 53804102
dl-4-625-907-sV-d
PAckAge cONTeNTS
Part Description
A Fixture
B Medium Base (E26) Socket
Adapter
Insert the fixture into the can.
Restore power to the electrical box.
Turn the light switch on to activate the fixture.
Within 3 seconds, turn the light switch off and back on
again to activate the night light. Flip the switch off and back
on again to return to downlight mode.
noTe: The main light will not provide light output when
the night light is illuminated.
53805102
Quantity
1
1
A B