En: Installation Instructions - GE Security DC138 Instrucciones De Instalación

EN: Installation Instructions

Legend for Figures
1 Magnetic contact
2 Installation and connection diagram
A Contact
B Magnet
3 Distance diagram
A Proximity/switch-on distance
B Distance/switch-off clearance
C Tolerance zone
D Contact
E Magnet
4 Connection
A, B, C, D Connection cable
Note: B and D are the 2 twisted cables for the tamper loop.
E Switching part (NC)
F Tamper protection (internal reed)
G EOL resistor
Description
The magnetic contact and the magnet must be mounted facing
each other in a window frame/door leaf and window
surround/door surround.
Caution: The EN grade 3 flush-mounted magnetic contact DC138
was specially developed for installation in ferromagnetic
materials.
When installing the snap-on metal flange mounting EF 8/20, a
material strength of 0.5 - 2.3 mm is permissible.
When mounting is complete, the magnetic contact's electrical
switching function must be checked (e.g. using a continuity tester
or multimeter).
The application of mechanical force, e.g., when mounting the
device on the casing may damage the glass body of the reed
switch.
Installation
Snap-on metal installation flange EF 8/20 on the contact and
magnet housing (see Figure 2).
Caution: Measure the supply lines electrically before connecting
them!
Distance Diagram
See Figure 3.
Minimum switch-on distance:
tolerance in z:
Table 2
Proximity/switch-on distance
Distance/switch-off clearance
2 of 9
9 mm,
max. +/- 3 mm
Switch-on Tolerance
distance [mm] [mm]
12 +/- 3
13 +/- 2
Technical Data
Flush-mounted magnetic contact DC138 for EOL zone types,
tamper protected.
Note: For front flush-mounted installation in ferromagnetic
materials.
Contact type 1 - pin NC contact
Switching distance 12 mm, +/- 3 mm
Switching voltage max. 100 V DC
Switching current max. 500 mA
Contact rating max. 6 W or 6 VA
Contact resistance max. 0.15 Ohm
Breakdown voltage > 250 V
Permissible operating max. 40 V
voltage
Connection cable LIYY 4 x 0.14 mm Cu tin-plated;
Suitable for LSA IDC method of termination
External cable color White
Internal conductor Blue (yellow pattern)
∅ 8 x 32 mm with installation flange EF 8/20
Contact dimensions
(for 20 mm drilled diameter)
∅ 3.2 mm x 2 m (DC138)
Cable dimensions
∅ 3.2 mm x 6 m (DC138S60)
∅ 6 x 19 mm neodymium, axially polarized,
Magnet
in ∅ 8 x 25 mm plastic sleeve with installation
flange EF 8/20 ( 20 mm drilled diameter)
Housing material S-B or A-B-S, flange PA6 GF 30
Color White
Temperature range - 25 °C to + 70 °C
Protection category VdS - environmental class III, IP 67
Scope of Delivery
• 1 magnetic contact ∅ 8 x 32 mm with 1 flange EF 8/20
• 1 magnet 6 x 19 mm neodymium in plastic sleeve
∅
8 x 25 mm with 1 flange EF 8/20
∅
European Directive
Tested & Certified
EN EN 50131-2-6 Grade 3 by VdS
VdS no. G110010 (Cl. C)
European GE Security B.V., Kelvinstraat 7, 6003 DH Weert,
Representative of The Netherlands.
Supplier
The goal of the EC directive on waste electrical and
electronic equipment is to minimize the
environmental and health impact of such
equipment. In accordance with this directive,
electrical devices bearing this symbol must not be
disposed of in the European public waste disposal
systems. European users of electrical devices must
now return all waste electrical and electronic
equipment for recycling. For more information,
please visit: www.recyclethis.info
Contact
See www.gesecurity.eu.
P/N 31495600.Y71 • REV 1.0 • ISS 18FEB10