Publicidad
Idiomas disponibles
Idiomas disponibles
Notes:
When using a vehicle' s 12 volt DC accessory outlet as a power source, be aware that some vehicles require you to turn on the
ignition to power the accessory outlet. Manufacturer strongly recommends that you leave the ignition of the vehicle turned on (NOT
in the accessory position) while operating the spotlight to avoid draining the vehicle battery.
When not in use, always turn off the light and disconnect the 12V DC power cord from the accessory outlet of your vehicle or other
DC power source.
WARNING: TO AVOID THE RISK OF PROPERTY DAMAGE:
• Never connect the unit to a positive grounded vehicle.
• The 12V DC Power Cord must only be connected to batteries with a nominal output voltage of 12
volts. The unit will not operate from a 6 volt battery and will sustain permanent damage if connected
to a 24 volt battery.
Using the hanging hook
The hanging hook at top allows you to position the spotlight for convenient, hands-free operation.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When the spotlight is hung by the hanging hook, do not shake the spotlight or the object that it is
hanging from. Do not hang the spotlight from any electrical wires or any object that it is not secure.
• Only use the hanging hook for hanging the spotlight. The hanging hook is not intended to support
additional weight. Do not attach anything additional to the spotlight or hang anything additional with
the spotlight on the hook or risk of breakage may occur.
CARE AND MAINTENANCE
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight
unit with a soft cloth moistened with a mild solution of water and detergent.
Bulb Replacement
1. Unplug the 12V DC Power Cord from the 12 volt DC accessory outlet of your vehicle or other 12
volt DC power source.
2. Push the rubber bezel forward toward the front of the spotlight to remove it.
3. Remove the molded handle cover from the handle.
4. Using a screwdriver, remove (counterclockwise) the six screws that secure the spotlight housing.
Set them aside.
5. Lift up and set aside the right side of the housing.
HANGING
HOOK
PHILLIPS
SCREWS
MOLDED
HANDLE
COVER
SL12VDCB _ManualENSP_120313.indd 4-5
LIGHT
REFLECTOR
RUBBER
RUBBER
BEZEL
O-RING
LENS
HALOGEN BULB
ASSEMBLY
Only replace the bulb in an
integrated assembly of lamp
holder, wire and tab.
HAIRPIN
RETAINING
RETAINING
WIRE
SCREW
LIGHT REFLECTOR
4
6. Lift off the glass lens and rubber O-ring and set them aside.
7. Carefully remove the reflector and bulb assembly.
8. Disconnect the bulb wire from the red power wire.
9. Unsnap the hairpin retaining wires from the reflector's flange.
10. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need
to completely remove this screw).
11. Lift out the bulb and detach wire.
12. Insert the replacement bulb into the reflector's flange.
13. Put back and secure the hairpin retaining wires.
14. Connect the bulb power wire to the red power wire.
15. Tighten the retaining screw on the flange.
16. Place the reflector in position in the body of the spotlight.
17. Replace the rubber O-ring and glass lens in the groove around the perimeter of the reflector.
18. Replace the right side of the housing so the screw holes are aligned.
19. Secure the spotlight housing with six Philip Head screws (clockwise).
20. Replace the molded handle cover onto the handle.
21. Replace rubber bezel.
22. Plug the 12V DC Power Cord into the 12 volt DC accessory outlet of your vehicle or other 12 volt
DC power source and operate switch to ensure proper operation of spotlight.
Note:
When handling a new halogen bulb, do not touch the glass portion of the bulb. Natural oils from your hands can cause the bulb to
fail. If necessary, clean the bulb with alcohol or a liquid window cleaner.
12 volt DC plug fuse replacement
The fuse in the plug end of the 12V DC Power Cord protects the spotlight. If the spotlight does not
operate, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 12 amp/250 volt fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the spotlight.
TROUBLESHOOTING
Problem
Recommendation
Unit will not operate
1. Make sure the Power On/Off Switch has been slid to the ON position
(up).
2. Check connection to the 12VDC power source.
3. Confirm there is a functioning 12VDC current.
4. Check the fuse inside the 12V DC Power Cord. If the fuse is open
(blown), replace the fuse following the instructions in this manual.
5. The halogen bulb may have blown. Check bulb filament. If the
filament is coiled and unbroken, the bulb is not blown. Otherwise,
replace the bulb following the instructions in this manual.
6. If the spotlight does not operate with a fuse and bulb you have
determined to be good, contact manufacturer at 1-877-571-2391.
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you need
assistance regarding accessories, please contact the manufacturer at 1-877-571-2391.
WARNING: The use of any accessory not recommended for use with this appliance could be
hazardous.
5
12/3/2013 10:24:37 AM
Publicidad
