Publicidad
Idiomas disponibles
Idiomas disponibles
IV.
ASSEMBLY OF HANDHELD REMOTE CONTROL
[NOTE: If you have already installed the wall control but do not wish to use the
handheld remote control, please proceed to Part V.]
A. Gently pull on remote control cover to separate top and bottom parts.
(See Fig. 6)
B. In order to use wall control as a handheld remote control, cut each wire on
one of the wall controls--use wire cutters to cut off each wire as close to the
wall control as possible. (See Fig. 7)
C. Install one 12-volt battery (included) in wall control. (See Fig. 7)
D. The dimmer switch (labeled DIM and ON) has been pre-set to the "ON"
position (DIM). If you do not wish to have dimming capability or are using
bulbs that are not capable of being dimmed, please move the switch to the
"OFF" position (ON). (See Fig. 7)
NOTE: Most LED and compact fluorescent bulbs are not compatible for use
with dimmer controls.
E. Attach black faceplate to front of wall control; press down firmly. (See Fig. 8)
F. Align holes in wall control with posts located on inside of TOP part of remote
control cover and press together firmly. Place wall control into BOTTOM part
of remote control cover, aligning posts in top of remote control cover with
post holes in the bottom. (NOTE: Make sure to align narrower ends of remote
control cover before closing.) Squeeze top and bottom of remote control
cover together until you hear a click at each end, indicating that the remote
control cover has closed completely. (See Fig. 8)
V.
AUTOMATED LEARNING PROCESS/ACTIVATING CODE
CAUTION: The wall control/handheld remote control can be programmed
to multiple receivers or fans. If this is not desired, turn wall switch off to any
other programmable receiver or fan.
A.
Restore electrical power and then, if using wall control, set slider switch on
wall control to the ON position. Within 60 seconds of turning on the wall
control, press and hold the OFF button on the wall control for 5 seconds or
until the fan switches to MEDIUM speed (or, if applicable, until the light blinks
twice).
B.
Turn power off again for at least 5 seconds and then turn power back on.
Within 60 seconds of restoring the power, press and hold the OFF button on
the handheld remote control for 5 seconds or until the fan switches to
MEDIUM speed (or, if applicable, until the light blinks twice).
C.
Test the fan function (and, if applicable, the light function) to confirm the
learning process is complete.
VI. REMOTE CONTROL--CARE AND OPERATION
A. Store the remote control away from excess heat or humidity.
B. To prevent damage to remote control, remove the battery if not used for long
periods of time.
C. Operation buttons on front panel of remote/wall control (See Fig. 9):
button
for fan speed HIGH
button
for fan speed MEDIUM
button
for fan speed LOW
button
for fan speed OFF
button
for lighted housing (or up-light) BRIGHTNESS
-
1
1
and ON/OFF
[not applicable on all fan models]
button
for light kit BRIGHTNESS and ON/OFF
-
2
2
[light kit sold separately]
button
for blade direction, REVERSE
(fan must be set on low before reversing
blade direction)
slider switch
for wall control ON/OFF
(switch not functional on handheld remote)
The light function is controlled by pressing the L1 or L2 button. Hold the L1
or L2 button down to increase or decrease light. Tap button quickly to turn
light(s) off or on. If you press button in excess of 0.7 seconds it becomes a
dimmer. The light varies cyclically in 0.8 seconds. The light button has auto
resume, so the light will stay at the same brightness as the last time it was
turned off.
VII. TROUBLESHOOTING GUIDE
Remote and/or wall control fail(s) to operate:
1. Make sure there is power to the receiver.
2. Make sure the switch housing has been re-wired correctly.
3. Make sure the battery in the handheld remote control and/or the wall control
is good.
4. The learning process between fan, handheld remote control and, if applicable,
wall control may not have been successful. Turn power off and repeat Part V
(Automated Learning Process) above.
remote
control
cover
Fig. 6
(top)
(bottom)
post
hole
remote control
cover, BOTTOM
wall control
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE
THE FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE OR
CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.
p. 2
wall control
wire
-
1
1
-
2
2
DIM ON
wire
12V battery
Fig. 6
post
hole
-
1
1
-
2
2
DIM ON
face-
plate
wall
remote control
control
cover, TOP
-
1
1
-
2
2
handheld
remote control
CAUTION:
CRAFTMADE Ceiling Fans
COPPELL, TX 75019
FOR CUSTOMER SERVICE, CALL: 1-800-486-4892
dimmer
switch
DIM ON
wire
Fig. 7
Fig. 8
Fig. 9
Publicidad
