Troubleshooting - DRAKE DIGITAL ESR-T200 Manual Del Usuario

Trouble Shooting
If you encounter any problems with the receiver, look through this section for a description of your problem.
Try solving the problem by following the given solutions. However, if after attempting all the recommended
actions you still cannot solve the problem, please contact your local service provider or system installer for
assistance.
Problem
(1) The receiver front panel
power indicator doesn't
light up
(2) No picture on your TV
screen
(3) Cannot use RF signal
output
(4) UHF (RF signal) output is
severely interfered, can
see only ghosting picture
(5) Poor picture quality
(6) No audio service
(7) No video service
(8) Do not have all the
channels available after
using "Search Channel"
(9) Cannot lock signal by
using "Scan One"
(10) No teletext
(11) Cannot receive channels
after moving the receiver
between cities
RECEPTOR DIGITAL MHP DRAKE ESR-T200
Solution
(a) Check the main lead and make sure the power plug is well plugged into a stable power
outlet
(b) Press "Standby" button on the remote control to see if the green light (power indicator) is
on.
(c) Check the set top box is in "Standby" mode or not by pressing "Standby" button on the
remote control.
(a) Make sure the connection between set top box and your TV matches the mode your TV
should be set to. For instance, if you use RCA connector you may choose external video
input mode in TV.
(b) Check the brightness level of your TV is high enough
(a) Check the output RF channel number set in the receiver matches the channel number
your TV is tuned to.
(b) Check the RF connectors are correctly and firmly connected, please also refer to the
receiver and your TV's user's guide for instruction of the connection.
(a) Check your TV set if it uses Italian standard channel table for RF signal input, 7MHz
bandwidth for all VHF and UHF channels. You can refer to TV set's user's guide or
consult TV set's manufacturer for details.
(a) Check the antenna and make sure it is aligned to the correct direction. Use the Signal
Quality option in OSD menu to check the signal's BER and RF Level when aligning the
antenna.
(b) If you use any kind of amplifier to boost the signal level, please check whether it works
well, and ask help from the antenna installer.
(c) Refer to solutions in item (2) and (3) above
(a) Check the receiver and your TV's volume are properly set and not in "mute" mode.
(b) Check the audio connectors are correctly and firmly connected
(c) To make sure the channel you are watching does not use AC-3 audio.
(d) Check the left and right audio channel. Sometimes the referred audio service is set in
only left or right channel.
(e) Scan this channel again by using "Search Channel" and see if the audio service will
come back.
(f) Check with the local TV stations. Sometimes they are just testing new services on their
TV or Radio channels.
(a) Check the video connectors are correctly and firmly connected
(b) To make sure the channels you tune to are no broadcasting DTV programs. ESR-T200
cannot decode HDTV programs.
(c) Scan this channel again by using "Search Channel" and see the video service will come
back.
(d) Check with the local TV stations. Sometimes they are just testing new video services on
their channels the video service may top every once in a while.
(a) Try "Search Channel" to scan all the channels again.
(b) If you still cannot get some channels please use manual scan to enter individual channel
frequency to search the missing channels one by one.
(a) Check the frequency you enter is exactly the center frequency of the wanted channel.
(b) Refer to solutions in item (4) on previous page.
(a) Make sure the channel you are watching carries teletext information.
(b) Check your TV and make sure it is teletext capable.
(c) Check your teletext capable TV is in teletext mode
(d) Select teletext page number, for instance 601
(a) Enter into OSD Menu and use "Factory Reset" to clear the channel Memory, then use
"Search Channel" to scan through all the channels again.
5