Moulinex AQUASPEED IM5214E0 Manual Del Usuario página 5

1800132109 IM5214 E0 FTG_110 x 154 10/02/14 10:42 Page1
Description
1. Spray nozzle
2. Anti-scale valve
3. Steam control
4. Spray Button
5. Turbo Button
6. Auto-Stop safety warning light
7. Ergonomic grip
(depending on model)
8. Electric power cord
9. Lock-System ring to open and close the Ultracord system
(depending on model)
Before first use
• Before using your iron with the steam function for the first time, we recommend that you operate it
in a horizontal position for a few moments, away from your linen. Under the same conditions, press
the Turbo button a few times
• During the first few uses, a harmless odour and smoke may be given off. This has no effect on the
use of the iron and will disappear quickly.
Preparation
What water to use ?
• Your appliance has been designed to operate using untreated tap water. However, it is necessary to operate
the Self-Clean function regularly in order to eliminate hard water deposits from the steam chamber.
• Heat concentrates the elements contained in water during evaporation.The types of water listed below
contain organic waste or mineral elements that can cause spitting, brown staining, or premature wear of the
appliance: water from clothes dryers, scented or softened water, water from refrigerators, batteries or air
conditioners, pure distilled or demineralised water or rain water should not be used in your Moulinex iron.
Fill the tank up to the
"MAX". Never fill the
appliance by holding it
directly under the tap.
Use
Adjust the temperature and the steam
• Set the thermostat control – fig.4, referring to the table below.
• The thermostat light comes on. It will go out when the soleplate is hot enough – fig.5.
RECOMMENDATIONS
• Your iron heats up quickly: so begin by ironing fabrics that are ironed at low temperatures first, then go on
to those requiring a higher temperature,
• If you turn down the thermostat, wait until the thermostat light comes back on before beginning to iron
again,
• When ironing fabrics with mixed fibres, set the ironing temperature for the most delicate fibre. For delicate
fabrics we recommend testing the fabric first on an inconspicious place eg (inside the hem).
FABRIC
LINEN
COTTON
WOOL
SILK
SYNTHETIC
(Polyester,
Acetate, Acrylic, Nylon)
Make sure that there is water in
the tank before using this button.
(depending on model)
.
• Check that the Ultracord system is properly locked.
• Unplug your iron before filling it.
• Set the steam control to "0" – fig.1.
• Take the iron with one hand and tilt it slightly, with the nose of the soleplate pointing down.
• To open the flap of the water tank, push the button – fig.2.
• Fill the tank up to the "MAX" line – fig.3.
• Close the flap of the water tank, until it clicks into place.
POSITION OF
THERMOSTAT CURSOR
•••
• Whether steam or dry ironing, you are able to use the spray button to dampen laundry to remove
stubborn creases – fig.6.
1
10.
Ultracord System
(depending on model)
11. Water tank opening button
12. Water tank filler flap
13. Integral anti-scale system
14. Thermostat indicator light
Goes out when the temperature has been reached
15. Thermostat control
for choosing the ironing temperature
16. Extra Stable heel
17. Soleplate
Filling the water tank
MAX
••
•
Spray Function (spray)
(depending on model)
If your water is very hard, it is
possible to mix tap water with
store-bought distilled or
demineralised water in the
following proportions : - 50% tap
water, - 50% distilled or
demineralised water.
In order to avoid water
dripping from the iron onto
the linen:
- Turn off the steam when
ironing silk or synthetic
fabrics.
- Set it at the minimum
position for wool.
STEAM SETTING
POSITION
0
= STEAM ZONE