LEGRAND WattStopper TDCL453P Instrucciones

No: 341149 1/16
Catalog Number(s) • Numéro(s) de Catalogue • Les Numéros de Catalogue: TDCL453P
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
READ AND SAVE THESE INSTRUCTIONS
To be installed by a certified electrician or other qualified
person.
WARNING – To prevent severe shock or electrocution,
always turn power off at the service panel before
installing this unit, working on the circuit, or changing
a lamp.
CAUTION: To reduce the risk of overheating and
possible damage to other equipment:
• Do not install dimmer to control a receptacle, a
motor-operated appliance, or a transformer-supplied
appliance.
• Use only with incandescent or compatible dimmable
CFL/LED bulbs which screw into conventional
incandescent lamp sockets (compatible bulbs listed
at www.legrand.us).
Connect to 120VAC, 60 Hz power source only.
A 10W minimum load is required.
Use copper wire only.
IMPORTANT NOTES:
1. All dimmers can be damaged by improper wiring. Check for short circuits prior to
installing the dimmer.
Procedure for short circuit check:
a. Disconnect power to circuit by removing fuse or turn circuit breakers OFF.
b. Install a switch instead of the dimmer. Turn the switch to the "ON" position.
c. Turn power ON. If the circuit breaker trips, a short is present. If the light fails
to turn ON and OFF with the switch, the wiring may be incorrect.
d. Correct wiring, if necessary and retest.
e. Install the dimmer only after the light operates properly with the switch.
2. Protect from dirt and dust. The dimmer can be damaged from contaminates
encountered during the construction process. If lighting is required prior to the
construction process completion, then a switch should be temporarily installed
in place of the dimmer. The dimmer should not be installed until the construction
process is complete.
Any dimmer damage due to improper installation is not covered under warranty.
DIRECTIONS
1. Disconnect power to circuit by removing fuse or turn circuit breakers OFF
before installing.
2. Remove wall plate and switch mounting screws, pull existing switch from wall box.
3. Disconnect existing switch from circuit. For 3-way installations: Identify the
"Common" wire (wire connected to the terminal marked common or odd colored
terminal). For new installation identify wire connected to power source or to the load.
INSTALLATION DIAGRAM FOR DIMMERS / SCHÉMA D'INSTALLATION DES GRADATEURS
Single Pole Installation / Installation unipolaire / Instalación unipolar
Neutral (White) / Neutre (Blanc) / Neutro (Blanco)
White
Blanc
Blanco
LIGHT
Green
LUMIÈRE
Ground Screw
LUZ
Vis de terre verte
Black
Tornillo verde de
Noir
puesta a tierra
Negro
Wire to Load
Connecter à la charge
Cable a carga
Figure 1 / Figure 1 / Figura 1
LIRE ET CONSERVER CES INSTRUCTIONS
Doit être installé par un électricien certifié ou une autre
personne qualifiée.
AVERTISSEMENT – Pour éviter tout choc électrique ou
une électrocution, toujours couper l'électricité au niveau
du panneau d'alimentation avant d'installer cette unité,
de travailler sur le circuit électrique ou de changer une
lampe.
ATTENTION : Pour réduire le risque de surchauffe ou
d'endommagement d'autres pièces d'équipement :
• Ne pas installer un gradateur pour contrôler une
prise électrique, ou un appareil ménager équipé d'un
moteur ou alimenté par un transformateur.
• À n'utiliser qu'avec des ampoules à incandescence ou
variable à luminosité CFL/LED ampoules compatibles
qui se vissent dans des douilles d'ampoules à
incandescence traditionnelles (ampoules compatibles
énumérés à www.legrand.us).
Connecter à une source de 120 VCA, 60 Hz
uniquement.
Une charge minimale de 10W est requise.
N'utiliser que des fils en cuivre.
DIAGRAMA DE INSTALACIÓN PARA ATENUADORES
120VAC 60 Hz
120 VCA 60 Hz
Hot (Black) 120 VCA 60 Hz
Chaud (Noir)
Cargado (Negro)
Wire to Source
120VAC 60 Hz
Connecter à la source
120 VCA 60 Hz
Cable a suministro
120 VCA 60 Hz
Do not wire this terminal
Ne pas raccorder cette borne
No cablear este borne
Traveler Wire to
hacia interruptor
Screw Pressure Plate Back Wire / Fil arrière avec vis et plaque de pression /
Cable trasero con tornillo y placa de presión
WattStopper
Toggle Dimmer: CFL/LED 4.5A (450W), 120VAC, 60Hz; Incandescent 700W, 120VAC, 60Hz
Gradateurs à Bascule: CFL/LED 4.5 A (450 W), 120 VCA, 60 Hz; Incandescents 700 W,
120 VCA, 60 Hz
Atenuadores de Palanca: CFL/LED 4.5 A (450 W), 120 VCA, 60 Hz; Incandescente 700 W,
120 VCA, 60 Hz
Installation Instructions • Instrucciones de Instalación • Notice d'Installation
4. Connect dimmer as shown in the installation diagram using #12 or #14 AWG
stranded or solid copper conductors. Strip wire using gauge on back of device
(Figure 1 or Figure 2).
5. Install dimmer in wall box, with word "TOP" on the strap right side up, using mounting
screws provided.
6. Attach wall plate and then restore power to circuit.
7. Dimmer may require adjustment to the low end setting to reliably start and/or remove
flickering in bulbs. To adjust, DISCONNECT POWER FROM CIRCUIT, and remove
the Wallplate. Use a small insulated, flat tipped screwdriver to adjust the trim pot
wheel, which is accessible via the slot (marked "CALIBRATION") provided on the
strap (Figure 3). Turn the wheel left to increase the minimum light intensity setting
and turn the wheel right to decrease light intensity. Next, install the Wallplate,
restore the power and test. Repeat above as necessary.
Note: Never adjust trim pot when circuit is live.
To re-calibrate settings turn the trim pot wheel all the way
towards the "-" sign and incrementally progress to "+" sign
until flickering is removed (refer to Step 7 above).
Note: This device should be installed after sheet rocking and
painting are completed.
Note: It is normal for the dimmer to feel warm during operation.
Use a separate neutral wire for each phase of a multiphase
system containing a dimmer, and for high power single phase
applications where flickering is present.
Any combination of dimmer models and other devices may be
ganged together. De-rate the maximum load according to the following table:
Rated Load
Incd./Hal. 700W
CLF/LED 4.5A
3-Way Installation / Installation 3 voies / Instalación de 3 vías
Neutral (White) / Neutre (Blanc) / Neutro (Blanco)
Hot (Black)
Chaud (Noir)
Cargado (Negro)
Green
Wire to Source
Ground Screw
120VAC 60 Hz
Vis de terre verte
Connecter à la source
Tornillo verde
120 VCA 60 Hz
de puesta a tierra
Cable a suministro
120 VCA 60 Hz
Traveler Wire to
3-Way Switch
3-Way Switch
Commun ver
Commun ver
l'interrupteur
l'interrupteur 3 voies
3 voies
Alambra común hacia
Alambra común
interruptor de 3 vías
de 3 vías
Figure 2 / Figure 2 / Figura 2
®
LEA Y CONSERVE ESTAS INSTRUCCIONES
Para ser instalado por un electricista certificado o
persona competente.
ADVERTENCIA – Para evitar descargas eléctricas
serias o electrocución, antes de instalar, trabajar en
el circuito o cambiar una lámpara de este atenuador
apague siempre el suministro eléctrico en el panel de
servicio.
PRECAUCIÓN: Para reducir el riesgo de
sobrecalentamiento y posibles daños a otros equipos:
• No instale un atenuador para controlar un
tomacorriente, un electrodoméstico que funciona con
motor o un electrodoméstico con transformador.
• Utilícese solamente con bombillas incandescentes
CFL o LED atenuables que se atornillan en
portalámparas incandescentes convencionales
(bombillas compatibles enumerados en www.legrand.us).
Conecte solamente a un suministro eléctrico de 120
VAC, 60 Hz.
Una carga minima de 10W es requerida.
Utilice únicamente alambres de cobre.
Figure 3 / Figure 3
3 Gang (or more) Installation
650W
4.5A
3-WAY SWITCH
INTERRUPTEUR 3 VOIES
INTERRUPTOR 3 VÍAS
120VAC 60 Hz
120 VCA 60 Hz
120 VCA 60 Hz
COM
COM
COM
Figura 3
Ground
Fil de terre
Alambre de tierra
White
Blanc
Blanco
LIGHT
LUMIÈRE
LUZ
Black
Noir
Negro