Orbit ArizonaMist 92100 Instrucciones De Operación

3/8 in. Booster PumP;
110 Volt installation and
oPeration instructions
introduction
Thank you for selecting the quality of Orbit
satisfactory and trouble-free service if proper installation and care is observed. Please read the installation and instruction
manual carefully to fully understand all labels before installing. This pump utilizes a grounding conductor with a grounding type
attachment plug. To reduce the risk of electrical shock, only connect to a properly grounded, grounding type receptacle.
ThIS PUMP IS NON-SUBMerSIBle.
WaRninG
risk of electric shock. This pump is supplied with a grounding conductor and grounding type attachment plug. To reduce the risk
of electric shock, be certain that it is connected only to a properly grounded, grounding type receptacle.
Caution
Unplug the pump before servicing this unit.
■
To reduce the risk of electrical shock, install with all
■
electrical components above grade.
Install with all electrical components above ground and
■
with the properly grounded electrical outlets.
installation
Determine the location of the pump before proceeding.
■
Consider your water and power locations and locate the
pump within range of both resources.
Always install the appropriate water filter (Orbit
■
Mist Model # 10109) between the pump and the water
®
source.
Before installing the mist line to the pump, run water
■
through the filter for at least 30 seconds. This will flush
any debris that may be is in the line or in the filter.
operation
a pressure reducer is strongly recommended if your
■
standard hose faucet pressure is greater than 40 PSi.
Before operating the system, be sure the outlet pressure is
■
relieved to prime the pump.
Check the system to be sure all lines are installed securely
■
to the pump and the electrical cord is plugged into the
appropriate socket.
Turn on the water source to have water pressure to
■
the pump.
Orbit Irrigation Products, Inc.
®
North Salt lake, UT 84054 USA
www.orbitonline.com | 1-800-488-6156
© 2007 Orbit Irrigation Products, Inc.
®
All rights reserved. All trade names are registered
trademarks of respective manufacturers listed.
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
|Arizona Mist and the 3/8 in. 110 volt Booster Pump. You will enjoy many years of
® ®
|Arizona
®
1
dimensions:
proof no:
flat: w: 8.5" h: 11"
date:
11.11.08
finished: w 8.5" d: 0" h 11"
des: MZ spck: SMZ
colors
job no:
N/A
client:
Orbit
sku: 92100
upc:
N/A
additional instructions:
· LB412018
file name: 92100-24 rE.indd
·
software:
InDesign CS3
Optimal water inlet pressure is 40 PSI.
■
Maximum working pressure is 160 PSI.
■
This pump is for use outdoors with cold water only.
■
Do not use with flammable liquids.
■
This pump has been evaluated for use with cold water only.
■
The 3/8 in. mist lines should be installed in the ports located
■
in the front of the pump.
The inlet and outlet ports are clearly marked to insure the
■
lines are installed correctly.
The booster pump is not equipped with an automatic valve.
■
When shutting down the system, the water source must be
turned off to keep the system from running at line pressure.
This pump should be securely fastened to a fixed post or
■
wall. Be sure to use appropriate wall anchors when
fastening to a stucco wall.
The power switch is located on the side of the housing.
■
Switch the pump to the ON position.
This pump is fitted with a thermal protection switch that will
■
prevent the unit from damage due to overheating. This
switch is automated and will shut the pump off prior to any
internal damage to the unit. Operation will typically resume
within one hour of automatic shut-off.
color color
Registration non printing non printing
PMS
PMS
BLACK ???? ????
MoDEL 92100
PN 92100-24 re
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
PMS
????
© 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.