Air Supply - Matco Tools MT2868 Instrucciones De Operación

feaTures
• Dual piston for fast material removal
• Sanding pad has positive locking clamps and can also use PSA paper.

aIr suPPly

Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI
at the tool while running free. Higher pressure and unclean air
will shorten tool life because of faster wear and may create a
hazardous condition.
Water in the air line will cause damage to the tool. Drain the air
tank daily. Clean the air inlet filter screen on at least a weekly
schedule. The recommended hook-up procedure can be viewed
in Figure 1.
The air inlet, used for connecting air supply, has standard 1/4" NPT
American Thread.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be
3/8" I.D. and fittings should have the same inside dimensions.
Whip Hose
Do Not In stall
Quick Coupling Nipple
Here
Leader Quick Coupler
Hose
WarranTy
Matco warrants this air tool for a period of 1 year to the consumer.
We will repair any MT Series air tool covered under this warranty
which proves to be defective in material or workmanship during
the warranty period. In order to have your tool repaired, return
the tool to any of the Matco Authorized Warranty Centers listed,
freight prepaid. Please include a copy of your proof of purchase
and a brief description of the problem. The tool will be inspected
and if any part or parts are found to be defective in material
or workmanship, the tool will be repaired free of charge and
returned to you freight prepaid.
This warranty gives you specific rights. You may also have other
rights which vary from state to state.
The foregoing obligation is Matco's sole liability under this or any
implied warranty and under no circumstances shall Matco be
liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or
exclusion may not apply to you.
MT2868
MT2868 DUAL PISTON STRAIGHT LINE SANDER
Filter
Nipple
Oiler Regulator
TrOuBleshOOTIng
Other factors outside the tool may cause loss of power or erratic
action. Reduced compressor output, excessive drain on the air line,
moisture or restrictions in air pipes or the use of hose connections
of improper size or poor conditions may reduce air supply. If
outside conditions are in order, and the tool still performs
erratically, disconnect tool from hose and take tool to your
nearest Matco authorized service center.
luBrIcaTIOn & MaInTenance
Lubricate the tool daily with a good grade of air tool oil. If no
air line oiler is used, run 1/2 ounce of oil through the tool. The
oil can be squirted into the tool air inlet or into the hose at the
nearest connection to the air supply, then run the tool. A rust
inhibitive oil is acceptable for air tools.
Air Supply
Drain Daily
fIg. 1
MaTcO aIr cOMMand
Tool Repair SV
1330 Commerce Dr.
Stow, OH 44224
(800) 433-7098
dIscOunT TOOl rePaIr
3433 Losee Rd. #1
North Las Vegas, NV 89030
(702) 657-6570
PneuTOOl ParTs & serVIces cO., lTd
33 Haas Road
Toronto, Ontario
M9W 3A1 Canada
(416) 748-1200
(888) 748-1201 (Toll-Free in Canada)
dIVersIfIed POWer Inc,
90 Buttermill Avenue,
Vaughan, Ontario
L4K 3X7 Canada
Tel: 905-760-9077
Toll Free: 800-821-7975
3
aIr InleT
fIg. 2
03/19/12