Bestway 58367 Manual De Instrucciones página 5

Section II: Hose Configuration for
Backwashing and Rinsing
NOTE: Ensure the Control Valve is set to the Closed function. Your
pool should be filled with water, make certain all of the pool's Debris
Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E). If yes,
assemble your sand filter referring to method A; if no, assemble your sand filter referring to
method B.
Method A(see Fig. A-1)
1. Attach one end of the hose (23) to the sand filter's Port B; screw the threaded locking ring
into position.
2. Connect both ends of hoses (Φ32mm) to the pool valves marked "B", place the loose Hose
Clamps (P6124) on the end of Hoses. Connect both free ends of hoses (Φ32mm) to the
T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose(23) to the T-joint(25), screw the threaded locking ring into
position.
4. Remove the Stopper Plugs from the pool's outlet valves (marked "B") and insert with the
Debris Screens. With the Hoses and Debris Screens in position, tighten the Hose Clamps.
Method B(see Fig. B-1)
1. Attach one Hose (23) to the sand filter's Port B; screw the threaded locking ring into
position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded
locking ring into position.
3. Open the connection valve.
NOTE: You can refer to pool manual for connection valve's installation instructions.
4. Screw the other Hose (23) to Port D and place the opposite end in drain area.
Section III: Backwash and Rinsing
Backwash and Rinsing must be performed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT: This procedure removes water from the pool, which you'll need to replace. Switch off the sand filter immediately if water levels near the
pool's Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
NOTE: It is imperative to check that the hydraulic connectors are closed.
NOTE: Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig.E), and referring to B-2 if not. The assembly methods are the same.
1. Detach the Hose (23) from Port D.
2. Attach the Hose (23) to the Control Valve,s Port A; screw the threaded locking ring into position.
3. Connect the other end of Hose (23) to the pool's Inlet A.
4. Open the connection valve.
NOTE: You can refer to pool manual for connection valve's installation instructions.
23 (1.5m)
B
A
Fig.A-2
23 (1m)
B
25
Fig.E
B
A
23
5
Pool
B
P6124
A
P61408
D
Fig.A-1
B
Pool
B
A
D
Fig.B-1
B
B
A
Fig.B-2
23
B
B
>1/2 in
B
P6680
23 (1m)
Water level
>1/2 inch
Liner
23
Water level
>1.2 inch
Liner
S-S-004292