Preparing To Install - BESAFE iZi Modular Manual Del Usuario

10

Preparing to install

• Adjustable head rest (1a)
• Shoulder straps (2x) (1b)
• Side support (1c)
• Harness buckle (1d)
• Seat cushion (1e)
• Central adjuster (1f)
• Reclining handle (1g)
• Release handle head rest (1h)
• Front brace (1i)
Installation of the seat on the i-Size base
1. Check if the ISOfix and floor support indicators on the base are
green. (2)
2. Make sure that the front brace is installed on the base. The
operation of the front brace is described in the user manual for the
base. (2)
3. Make sure that the seat is always in the release position when you
want to install the seat on the base or take the seat off the base.
The two yellow arrows on the seat and the base must be aligned.
(3) Use the reclining handle to adjust the recline position, see
step 6.
4. Position the seat in the correct position on the base untill it clicks
with the base and the indicator at the front shows green. (3)
5. When the seat is positioned rearfacing on the back seat of the
vehicle, you should, if possible, push the front seat of the vehicle
backwards, so that it is in contact with the child seat (4). If it is not
possible to obtain contact with the child seat, push the back rest of
the front seat of the vehicle forward as far as possible.
6. The seat can be taken off and turned around by pulling the seat
release handle at the front of the base (5,6). Make sure that the
two yellow arrows on seat and seatbase are aligned; this is the only
position where you can take off the seat.
7. The seat should only be turned around to forward facing when the
child is minimum 88 cm or 15 months. BeSafe recommends to use
the seat rearfacing for as long as possible.
8. When the seat is positioned forward facing, the front brace has to
be in position 1. (7)
9. The seat cannot be turned around in the BeSafe iZi Modular RF.
This seat is only to be used rearfacing.
10. The seat can be reclined by pulling the reclining handle at the front
side of the seat. (8)
11. In a rearfacing position the seat should only be used in the 2 most
reclined positions. (9)
12. The leg room of the seat, in rearfacing position, can be made larger
by pulling the front brace box out from the base. The front brace box
has 3 positions. To adjust the front brace position, the seat has to be
taken off and the base should be released from the ISOfix. (10)
13. The seat is delivered with removable SIP+ (side impact protection +).
This extra side impact protection should be used on the doorside of
the vehicle. It can be connected by slotting between the seatshell and
the fabric. The seat already offers high level integrated side impact
protection. This extra side impact protection improves the protection
in the side impact still further. (Not on all models) (11)
Removal of the seat of the i-Size base
1. The seat can be taken off by pulling the seat release handle at the
front of the base. Make sure that the two yellow arrows on seatbase
and seatbase are aligned; this is the only position where you can take
off the seat.
Positioning of the child
1. Check that the shoulder strap slots are level with your child's
shoulders. (12)
2. Pull the shoulder straps up while pressing the button of the central
adjuster. (13)
3. Open the harness buckle. (14)
4. The height of the shoulder straps and the head rest can be adjusted
by pulling the release handle upwards at the back of the head rest
and pulling the head rest up or down. (15)
5. Position the shoulder straps over the marking at the sides of the seat
to use the magnets to keep the harness open while you position the
child. (16)
6. When the child is positioned, place the shoulder straps over the
child's shoulders and close the buckle: CLICK! (17)
7. Pull the harness strap through the central adjuster in the direction of
the arrow straight up/forwards. Continue pulling until the harness is
a comfortable but a firm fit. (18)
11