Fein GRIT GXR Instrucciones De Uso página 8

en
8
Original Instructions for radius grinding module.
Symbols, abbreviations and terms used.
The symbols in the Instruction Manual and on the
machine shall aide in directing your attention to possible
hazardous situations when working with this machine.
Symbol Term, meaning
Action
General mandatory sign
Read documentation
Danger warning
European conformity symbol
For your safety.
Do not use this machine before you have thor-
oughly read and completely understood these
operating instructions, including the figures, speci-
fications, and safety regulations.
Read and observe the operating instructions of the
GX75 belt grinder, which is to be mounted to this
machine.
These operating instructions should be kept for later use
and enclosed with the power tool, should it be passed on
or sold.
Use only the fastening material provided for mounting the
radius grinding module to the belt grinder. When mounted
incorrectly, the radius grinding module can loosen itself
from the belt grinder during the working procedure and
lead to serious injuries.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations. The
dust mask or respirator must be capable of filtrat-
ing particles generated by your operation. Pro-
longed exposure to high intensity noise may cause
hearing loss.
Make sure that all clamping levers and clamping fixtures
are firmly tightened. If the machine suddenly starts to
lower itself or if the work piece becomes loose during
the working procedure, serious injuries can result.
At a glance.
1 Belt tension lever (GX75)
2 Cover/stop (GX75)
3 Spark guard (GX75)
4 Star-knob bolt for dust box (GX75)
5 Grinding rest (GX75)
6 Dust collector (GX75)
7 Lever for swivel device (GX75)
8 Side cover (GX75)
9 Bolts/nuts for alignment of radius grinding module/belt
grinder
10 Spark guard
11 Spark guard wing bolts
12 Feed lever
13 Mounting lever
14 "Centre height" adjustment lever (pipe centre)
15 Clamping lever for "Centre height" adjustment
16 "Grinding depth/depth stop" adjustment
17 Table adjusting Cank
18 Collection receptacle
19 Protective covers/side cover
20 Locking screw for contact roller
21 Contact roller
22 Hand wheel
23 Work piece quick-clamping lever
24 Clamping lever for angle adjustment
25 Scale
26 Clamping jaws, fixed
27 Holding device/magazine for contact rollers
28 Rollers
Intended use of the machine.
The radius grinding module GXR is to be used together
with the GX75 belt grinder and exclusively for grinding
off pipe ends with diameters between 16 and 76 mm.
Mounting instructions (Figure 1 + 2 + 3).
Belt grinder GX75.
Before any work on the machine itself, pull the power
plug from the socket outlet.
Dismount the spark guard (3).
Dismount the grinding rest (5), the dust collector (6)
and the star knob bolt (4).
Open the side cover (8).
Loosen the belt tension lever (1) and remove the
grinding belt.
Close the side cover.
Loosen the lever for the swivel device (7) and posi-
tion the belt grinder approx. level.
Radius grinding module GXR.
Take the module out of the packaging and mount the
accessories as described in the data sheet.
Attach the radius grinding unit to the belt grinder and
align the bolt bores.
Connect both units with the two mounting levers
(13).
Clamp the lever for the swivel device (7).
Fill up the collection tank (18) halfway with water.
Position the collection tank between the support
columns of the radius grinding module.
Caution! Danger of fire when operating the module
without water filled in the collection tank!