Replacing The Battery; Regulatory Information - Interlogix RF-4041-07-2 Hoja De Instalación

Ocultar thumbs

Contenido

página de 17

/ 17
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

System status

System disarmed

System armed (away and stay)

System in alarm (intrusion event,

life safety)

System trouble (can't arm)

Keyfob low battery

In case the user is out-of-range of the receiver, this will be

indicated with the LED flashing yellow 2 times.

The keyfob will send a low battery signal when the battery

voltage goes below 2.2 V and it will also be reported to the

panel if the keyfob is learned into the panel.

Stay mode options

Single press of the button

active – interior zones are bypassed.

If you press the button again, Stay Instant mode activates −

your entry/exit delay zones will not be bypassed anymore and

will become instant.

If you press the button a third time, Stay Night mode activates

− in addition to entry/exit zones, also zones set up as "night

zones" will become instant. This prevents even authorized

users from entering the protected area unless it is disarmed

first (for example by someone inside the Stay area).

Replacing the Battery

Because keyfobs are non-supervised devices, a low battery

signal will only be received by the control panel when the

device is within range of the receiver and a button is pressed (if

the device is not in use, no low battery signal will be sent until

a button is pressed). When the device is carried beyond the

range of the receiver and/or is seldom used/tested, the battery

could wholly deplete without a warning of the battery condition

being sent to the panel. If the LED on the device appears dim

or does not turn on when a button is pressed, it is a warning

that the battery may be low or depleted and should be

replaced. To ensure proper functionality, test the device weekly

and follow these simple steps to replace the battery when

necessary:

With a key or small screwdriver, press the black tab

located at the bottom of the remote (Figure 1) and slide

the chrome trim off.

Carefully separate the front and back piece of plastic to

reveal the battery.

Replace with a CR2032 battery ensuring the + side of the

battery faces up (Figure 2).

Re-assemble the plastics and ensure they click together.

Ensure the notch in the chrome trim is aligned with the

back of the plastic. It will only go on one way (Figure 3).

Specifications

Compatibility

Interlogix LoNa transceivers (e.g. ZeroWire)

433.65 MHz

Wireless operating

frequency

2 / 16

LED indication

Green flashing LED for 1 second.

Red flashing LED for 1 second.

LED alternates flashes between

red and green 2 times, then stays

red for 3 seconds indicating an

alarm condition.

LED flashes yellow for 1 second.

LED flashes yellow 3 times.

makes the normal Stay mode

Power output

-9 dBm EIRP

Battery

3V lithium CR2032

Battery Life

5 years

Weight

42.5 g

Gross weight with

45.3 g

packaging

Packaging dimensions

41 x 21 x 67 mm

Power supply type

EN50131-6:2008 Type C

Housing

EN 50131-3:2009 ACE Type B, portable

Operating environment

Temperature

0 to 45°C (32 to113°F)

Relative humidity

5 to 95% noncondensing

Regulatory information

Placed on the market by:

Manufacturer

UTC Fire & Security Americas Corporation, Inc.

3211 Progress Drive, Lincolnton, NC, 28092,

USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, Netherlands

Certification

EN 50131-3:2009

Environmental Class II

Security Grade 2

Tested and certified by Telefication B.V.

Product warnings

THESE PRODUCTS ARE INTENDED FOR

and disclaimers

SALE TO AND INSTALLATION BY QUALIFIED

PROFESSIONALS. UTC FIRE & SECURITY

CANNOT PROVIDE ANY ASSURANCE THAT

ANY PERSON OR ENTITY BUYING ITS

PRODUCTS, INCLUDING ANY "AUTHORIZED

DEALER" OR "AUTHORIZED RESELLER", IS

PROPERLY TRAINED OR EXPERIENCED TO

CORRECTLY INSTALL FIRE AND SECURITY