Gerber VIPER Manual Del Usuario

VIPER TM , AQUA SAVER
TOILETS WITH FLUIDMASTER
DIRECTIONS FOR TANK TO BOWL ASSEMBLY
This water closet has been designed for easy installation. Conventional
fittings have been used throughout so that the working parts and operation
of this assembly may be easily understood.
1.
Before assembling tank (B) to bowl (K) check tightness of lock nuts on both flush valve and
fill valve.
2. Assemble tank bolts (D) in tank with rubber washers (E) and plastic wing nuts (F).Wing
nuts should be tightened by hand sufficiently to compress rubber washers and insure water
seal.
3. Assemble bevel washer (G) to flush valve shank so that lock nut is enclosed in recess,
making sure that the entire surface of the washer is in contact with the tank bottom.
4. Place two channel pads (H) in recesses on back of bowl ledge to prevent china-to-china
contact.
5. Place tank assembly in position. All parts are supplied.USE NO PUTTY. Plastic wing nuts
(F) are tightened by hand sufficiently to prevent rocking ; and since the tank bolts are
already sealed, the tank can be leveled by the relative amount that each wing nut is pulled
down on the three points of contact ...beveled washer (G) and two channel pads (H).
6. Plastic bolt caps and washers (J) are provided to be used as indicated in the illustration.
7. The fill valve coupling nut (l) is provided to connect the water supply line to the fill valve
USE NO PlPE DOPE!HAND TIGHTEN ONLY! OVERTIGHTENING MAY SPLIT THE FILL
VALVE AND WILL VOID THE WARRANTY!
8. Make sure refill tube adaptor is attached to the top of the flush valve overflow tube.
Note:Flow from the refill tube must be positioned directly over the overflow tube.
9. IMPORTANT:Always clear sand and rust from system.
• Remove valve top by lifting arm and rotating top 1/8 turn counterclockwise.
• While holding a container over the uncapped valve to prevent splashing,
turn water supply on and off a few times. Leave water supply off.
• Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TOP
IS TURNED TO THE LOCKED POSITION.VALVE MAY NOT TURN ON IF TOP IS
NOT FULLY TURNED TO THE LOCKED POSITION.
10. Adjust water level in tank to marked water line. Squeeze the water level adjustment clip (L)
and move the float cup (M) up or down along the stainless steel link (N).
11. Check action and nut tightness (left hand thread) of tank lever (C). Also,check looseness
of flapper chain (there should be slight slack in chain when at rest) and seal of flush valve
flapper.
DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING
CHLORINE OR BLEACH. Use of in-tank drop-in cleaners containing chlorine or
bleach VOIDS FLUIDMASTER™ WARRANTY and WILL RESULT IN DAMAGE to tank
components and may cause flooding and property damage.
DO NOT EXPOSE PLASTIC TRIM PARTS TO STRONG OXIDIZING AGENTS, CHLORINE,
OR ACID LEVELS OF LOWER THAN 5.0 pH. SOME BOWL/TILE CLEANERS CONTAIN
SUCH AGENTS.
TANK TYPE BOWL CLEANERS CAN CAUSE TANK COMPONENT FAILURE AND
DAMAGE. OUR WARRANTY EXCLUDES SUCH FAILURES.
VIPER™, AQUA SAVER™, ALLERTON™ and Maxwell
FLUIDMASTER ® is the registered trademark of Fluidmaster lnc.
PN 8014 , rev. 12-09
TM , ALLERTON TM , MAXWELL ®
® AND 2" FLUSH VALVES
® are trademarks of GERBER Plumbing Fixtures LLC.
(1) B/C Coupling Nut
Écrou de raccordement
B/C Tuerca de unión
(2) Plastic Bolt Caps & Washer
Rondelle et chapeau de boulon en plastique
Casquete plástico para tornillo y arandela
(k) Bowl
Cuvette
Taza
NOTE: Parts with " are included in unit bag
REMAQUE: Les piéces portant un " sont incluses dans ie sac.
AVISO: Las partes con " están incluidas en la bolsa de la unidad.
METAL/COPPER GALVANIZED METAL FLANGED METAL SPIRAL
TUBING PIPE (SEE NO TE) TUBING TUBING
LOCK NUT LOCK NUT
LOCK NUT
EXISTING
O-RNG
WASHER
CONE
WASHER
EXISTING
COUPLING COUPLING
COUPLING
CAUTION: NUT NUT
NUT
DO NOT
USE
WATER
CONE SHUT-OFF WATER
WATER
SHUT-OFF
SHUT-OFF
WASHER
OR
Use existing Use existing spiral cone
O-RING
coupling nut washer. Fluidmaster cone
WITH
PLASTIC and washer. washer may not seal
completely on spiral type
SUPPLY
LINE. supply line.
Float Cup
Coupelle flottante
Flotador
(A) Tank Cover
Couvercledu réservoir
Tapa del tanque
(B) Tank
Réservoir
Tanque
(C) Tank Lever
Levier du réservoir
Palanca del tanque
(2) Tank Bolt
Boulon de réservoír
Tornillo de tanque
(2) Rubber Washer
Rondelle en caoutchouc
Arandela de goma
(4) Plastic Wing Nut
Écrou papillon en plastique
Tuercas de orejas plásticas
(1) Bevel Washer
Rondelle oblique
Arandela cónica
(2) Channel Pads
Coussinet de canal
Tacos acanalados
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
LOCK NUT
potentiial flooding.
EXISTING
CONE
WASHER
COUPLING
NUT
FOR GALVANIZED
PIPE ONLY. you
WATER must break out
SHUT-OFF
the center of
COUPLING NUT
by striking it lightly with ahammer
or blunt end of screw driver handle.
Discard center portion. Also,use
O-RING instead of cone washer.
Stainless Steel Link
Tige d'acier inoxydable
Varilla de acero inoxidable
Water Level Adjusting Clip
Agrafe de réglage de
niveau d'eau
Sujetador de graduación
del agua