Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 372673 Traducción Del Manual Original

GB
e) Operate and maintain the sander or polisher as recommended in the
instruction handbook, to prevent an unnecessary increase in vibration
levels
f) Hold the tool with a light but safe grip, taking account of the required
hand reaction forces, because the risk from vibration is generally
greater when the grip force is higher
Additional Safety Instructions for Pneumatic Power Tools
Air under pressure can cause severe injury:
• Always shut off air supply, drain hose of air pressure and disconnect
tool from air supply when not in use, before changing accessories or
when making repairs
• Never direct air at yourself or anyone else
• Whipping hoses can cause severe injury. Always check for damaged or
loose hoses and fittings
• Whenever universal twist couplings (claw couplings) are used, lock
pins should be installed and whipcheck safety cables should be used to
safeguard against possible hose-to-tool or hose-to-hose connection
failure
• Do not exceed the maximum air pressure stated on the tool
• Never carry an air tool by the hose
Sand Blasting Equipment Safety
WARNING: Abrasive blasting with sands containing crystalline silica can
cause silicosis, a serious respiratory disease that can be fatal.
WARNING: Never blast abrasive material towards a source of heat or
ignition, as this may cause a fire or an explosion.
WARNING: Dust emissions from sandblasting may contribute to the
formation of explosive atmospheres. Ensure proper ventilation and take
precautions to prevent dust explosions.
• ALWAYS wear adequate personal protective equipment, including eye
and hearing protection, suitable gloves, long sleeves and protective
clothing when operating a sandblaster.
• If large amounts of dust are created, helmets or hoods with air supply
may be necessary
• Work gloves must protect the full forearm; protective clothing must
provide suitable protection from rebounding abrasives
• Sandblasting operations are noisy. ALWAYS wear adequate hearing
protection where sound levels exceed 85dB(A)
• Sandblasting equipment is likely to develop an electrostatic charge
during operation. If an electrostatically conductive blast hose is not
available the blast nozzle must be grounded
• NEVER direct the outlet nozzle towards people or animals
• DO NOT use other fluids than clean, dry, unoiled compressed air to
power sandblasting equipment
• Wet, oily or otherwise contaminated compressed air will cause the
abrasive to cake, and clog the sandblasting equipment
• NEVER use sandblasting equipment to spray solvents, acids or caustic
agents
• DO NOT work near flammable items. Abrasive striking metal can cause
sparks which may ignite flammable materials.
• Carefully cover areas of the workpiece that must not be sandblasted
(e.g. insides of engine blocks, cylinder bores, and other functional
surfaces)
• Refer to the abrasive manufacturer's instructions with regards
to additional safety warnings, usage recommendations and disposal
procedures
• ALWAYS disconnect the sandblasting equipment from the air supply
when relocating or refilling the abrasive container
6

Product Familiarisation

1
Collection Bag
2 Hook & Loop Strap
3 Collection Bag Port
4
Outlet Connector
5
Barrel
6 Trigger
7 Handle
8 Air Inlet
9 Quick Connector
10 Canister Connector
11 Sand Canister
Accessories (not shown):
• 4 x Nozzle Adaptors

Intended Use

Compressed-air-powered sandblasting gun that sprays abrasive material on
to surfaces in order to remove coatings, rust and contaminants. Ideal for the
removal of paint and light corrosion within tight spaces.

Unpacking Your Tool

• Carefully unpack and inspect your new tool. Familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If any
parts are missing or damaged, have such parts replaced before
attempting to use this tool

Before Use

WARNING: Always disconnect from the air supply and depressurise
before cleaning or carrying out any maintenance.
Fitting the quick connector
Note: This tool is supplied with two different male air line quick connectors:
EQ-4
commonly used
in Europe
• Please choose the connector that is compatible with the air line system
you are using, and install as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick
Connector (9). This will help to maintain an air-tight seal
Note: Apply PTFE tape tightly, and in a clockwise direction, so it does not
come off when the thread is screwed into the tool.
2. Remove the protective plug from the Air Inlet (8)
3. Using a spanner (not included) screw the Quick Connector into the Air
Inlet located at the base of the handle
4. Connect to air line, pressurise carefully, and carry out a leak check
(e.g. by spraying small amounts of soapy water on to the outside of the
connectors)
• Air lines fitted with matching female quick connectors will now be a
push fit to the tool
EN-6
mainly used
in the UK