Using The Timer Function; Cleaning And Storage; Technical Specifications - Perel Tools CBAL2 Manual Del Usuario

Using the timer function

•
Press the TIME button [C] to go to timer mode (TMR is displayed).
Note: when no activity is detected within ±20s, the scale automatically returns to normal clock display.
•
Press and hold the TIME button [C] until the seconds-indication starts flashing.
•
Press the UNIT button [B] to increase the value. Press and hold for faster adjustment.
•
Press the TIME button [C]; the minutes-indication starts flashing.
•
Press the UNIT button [B] to increase the value (max. 99min.). Press and hold for faster adjustment.
•
Press the TIME button [C] again to start the countdown. Press the UNIT button [B] at any time to
temporarily halt the countdown, press again to continue.
Note: during countdown it is possible to use the scale.
•
When the countdown timer reaches 0, an alarm will sound through the buzzer [E]. The alarm will last for
±30 seconds; to stop the alarm sooner, press any button.
•
To reset the timer to 00:00, press and hold the unit button [B] for ±2 seconds.
Using the scale
•
Unfold the scale completely (scale platform [F] horizontal) and press the ON/ZERO button [D]. The display
shows HELO, followed by 0 or '- - - - '.
•
Press the ON/ZERO button [D] to reset the scale to 0. Place the ingredient(s) as close as possible to the
centre of the platform [F] and read the weight on the display [A].
Note: To switch between metric and imperial units, press the UNIT button [B]. The setting is memorized.
•
When the weight is over the maximum weight limit, the display [A] will indicate Err. Avoid exceeding the
maximum capacity as this will cause irreversible damage to the scale.
•
Press the ON/ZERO button [D] to reset the scale to 0 at any time. Place an empty container or bowl on the
platform and press the ON/ZERO button [D] to eliminate its weight (tare). The word TARE is indicated in
the lower left corner of the display [A].
Note: after ± 3 minutes of inactivity, the scale will return to clock mode.
Battery
6.
•
When the battery indication is shown in upper left corner of the display [A], replace the battery.
•
Open the battery cover on the back of the scale.
•
Replace the old battery with a new CR2032 battery, positive pole facing up.
•
Close the battery compartment.
•
Remove the battery when the device is not in use for a long time.
WARNING:
Handle batteries with care, observe warnings on battery casing.
Do not recharge batteries and do not puncture or throw in fire as they may explode.
Dispose of batteries in accordance with local regulations.
Keep the battery away from children.

Cleaning and storage

7.
•
Clean the scale with a slightly damp cloth. Never submerge the scale in water or use abrasive cleaning
agents.
•
All plastic parts should be cleaned immediately after contact with fat, spices, vinegar or strongly flavoured or
coloured food. Avoid contact with acid substances e.g. citrus juice.
•
The glass platform [F] is removable. Gently rotate counter clockwise to separate it from the rest of the scale.
To place it back, gently rotate it clockwise.
Note: the platform is NOT dishwasher safe.

Technical specifications

8.
capacity
resolution
weight
Use this device with original accessories only. Velleman nv cannot be held responsible in the event of
damage or injury resulted from (incorrect) use of this device. For more info concerning this product,
please visit our website www.perel.eu. The information in this manual is subject to change without
prior notice.
© COPYRIGHT NOTICE
This manual is copyrighted. The copyright to this manual is owned by Velleman Components nv. All worldwide rights reserved. No part of
this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the
copyright holder.
30/04/2009
3kg
1g
±500g
CBAL2
power supply
folded
dimensions
open
4
1 x CR2032 (incl.)
45 x 150 x 255mm
190 x 150 x 255mm
©2008 Velleman ® Components nv