Product Familiarisation - Silverline 613578 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 24
GB

Product Familiarisation

1
Blade Tension Adjustment Knob
2
Upper Blade Wheel
3
Blade Guard
4
Upper Blade Guide
5
Table Insert
6
Saw Table
7
Wheel Pads
8
Table Fastener
9
Lower Blade Wheel
10
Base
11
Lower Cover Lock
12
Upper & Lower Covers
13
On/Off Switch
14
Upper Cover Lock
15
Blade Tracking Adjustment Knob
16
Frame
17
Fence
18
Fence Clip
19
Motor
20
Dust Extraction Port
21
Table Lock Handle
22
Table Angle Gauge
23
Blade
24
Blade Guide Height Adjuster with Locking Knob
25
Table Fixing Screws
26
Upper Support Bearing Hex Screw
27
Upper Support Bearing
28
Upper Guide Pins
29
Hex Screws for the Upper Guide Pins
30
Hex Screw for upper assembly position adjustment
31
Upper Guide Pins Housing
32
Lower Blade Guard
33
Securing Nut for Lower Assembly
34
Lower Support Bearing
35
Hex Screws for the Lower Guide Pins
36
Table Alignment Bolt
37
Table Alignment Securing Nut
8
Accessories
• Push-stick
• Open ended spanner
• 2 hex keys
• Slotted screwdriver
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its
features and functions
• Ensure that all parts of the tool are present and in good condition. If any
parts are missing or damaged, have such parts replaced before attempting
to use this tool
Transportation
To transport the bandsaw, hold the base with one hand and the frame with the
other. Never lift the bandsaw by the motor or table, or other part of the unit
Assembly
CAUTION. Always ensure that the bandsaw is switched off and plug is
removed from the power point before making any adjustments
Bench mounting
• Set up the unit on a firm, flat surface so that the machine stands securely
and cannot tip over
• If the bandsaw is to be used in a permanent position or there is a danger of
the saw tipping due to the size of material that will be cut, you must secure
the bandsaw to a rigid work surface:
• Use the holes in the base as a template to mark and drill four holes in the
intended mounting surface (eg workbench). Secure the unit in position
using large bolts, washers and nuts (not supplied). Use nuts or washers
that are resistant to working loose as a result of vibration, such as split
locking washers
• Ensure the bolts are long enough to penetrate the workbench sufficiently
for a secure fix.
• Check that the fittings remain tight after first use
Installing the saw table (See Figs 3-5)
NOTE: Before setting up the bandsaw you will need to access the Lower
Support Bearing (34) and Hex Screws for the Lower Guide Pins (35) so it is
recommended that preparation procedures are carried out before installing the
saw table. (See Figs 3-5)
1. Remove the Table Fastener (8) if already fitted so that the blade will be
able to enter the slot
2. Move the Blade Guard (3) to a higher position using the Blade Guard
Height Adjuster (24) if necessary, to allow the saw table to be fitted
3. Slide the Saw Table (6) into position passing the blade through the blade
slot in the saw table so the blade teeth face the slot
4. Check that the Blade (23) is positioned exactly in the centre of the
aperture in the saw table
5. Secure the saw table with the three Table Fixing Screws (25) using the
supplied washers and nuts on the underside
6. Re-fit the Table Fastener (8)
7. Fit the Table Insert (5) in the table
NOTE: To remove the saw table, for example to gain access to the lower blade
bearing and guide pins, follow the above procedure in reverse
Dust extraction
For a cleaner, safer work environment fit a vacuum system to the Dust
Extraction Port (20).
Preparation
CAUTION : Always ensure that the bandsaw is switched off and the plug is
removed from the power point before making any adjustments
Tensioning the blade (See Fig 6)
• To increase the blade tension turn the Blade Tension Adjustment Knob (1)
clockwise
• Check the blade tension by applying pressure to the side of the blade at the
centre point between the upper and lower blade wheels; the blade should
be able to move only 1-2mm laterally
CAUTION: The blade may break if over-tensioned. Beware of injury
• If the blade has insufficient tension it may slip on the blade wheels
• Release tension from the blade if the bandsaw is not going to be used for
some time
• To release tension in the blade, turn the Blade Tension Adjustment Knob
(1) anticlockwise
• Don't forget to re-tension the blade before use

Publicidad

Tabla de contenido
loading

Tabla de contenido