TEKONSHA 3031-P Instrucciones De Instalación

Installation Instructions
Directives de Montage
Instrucciones de Instalación
Electric Trailer Brake Control
Wiring Adapter
Adaptateur pour câblage
de commande de frein de
remorque électrique
Adaptador del cableado de
control eléctrico del remolque
WARNING
ALWAYS read and follow all warnings and
instructions included with purchase before
beginning installation. Keep for future reference.
DO NOT exceed lower of towing manufacturing
rating (including in your vehicle owner's manual)
or specific amperage ratings stated on product.
ALWAYS read, understand and follow all warnings
and instructions printed on tow vehicle's battery.
ALWAYS wear safety glasses and use all safety
precautions during installation.
3031-037 Rev. A
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover
TUNDRA
1. Make sure the vehicle is off with the keys
removed from the ignition.
2. Locate access panel in the center of dash on
A
drivers side . Using a trim panel puller, locate
notch in panel and pry the panel out and away
from the dash being careful not to damage the
trim or panel. Unplug the housings attaching the
panel being careful not to damage locking tabs
B
and set aside .
3. Carefully pull the housing towards the access
panel and plug in the mating white housing
from the brake control adapter
4. Locate a suitable grounding point near the con-
nector such as an existing ground stud or drill
a 3/32" hole and secure the white wire using
the eyelet and screw provided. (Do not drill into
vehicle floor or bed.) Clean dirt and rustproofing
from area.
5. Locate a routing path for the adapter to exit
the bottom of dash.
NOTE
Use a flash light to shine light up though the
bottom of dash to locate a hole to exit the dash.
6. WARNING
Complete the installation per the electric brake
control manufacturer's instructions and mount
the unit as directed. Perform test procedures
as instructed.
Wiring Adapter Housing
(Containing Male Terminals)
TUNDRA
A
TUNDRA
B
TUNDRA
8/11/2017
C
7. After brake controller is installed, plug in
all connectors that were not used back into
the original housings and snap access panel
back into place.
NOTE
Vehicles not equipped with OEM trailer
tow package, may require fuses and relays
to complete output and battery feed circuits
(sold separately). Consult owners manual
for locations.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
Max. 3 AXLES: 6 BRAKES (18 amps)
Read vehicle's owners manual & instruction
sheet for additional information.
TACOMA
C
1. Make sure the vehicle is off with the keys
removed from the ignition.
2. Locate the vehicle's electric brake control
harness. The harness will be located underneath
and left of the steering column, behind kick
panel taped to another harness near the emer-
gency brake pedal. There will be a white 10-pin
connector that mates with the one on
the adapter.
3. Carefully remove tape and plug in the mating
white housing from the brake control adapter.
Plug the brake control adapter into the vehicle's
electric brake control harness connector. Follow
all brake control manufacturer's installation
instructions.
Wire Side
#5 Ground
#7 Trailer Brake
D
EF
PAGE 1 OF 3
#9 Vehicle Stop Lamp
#8 Fuse Trailer Brake Controller
TACOMA
D
TACOMA
E
TACOMA
F
4. Locate a suitable grounding point near the con-
nector such as an existing ground stud or drill
a 3/32" hole and secure the white wire using
the eyelet and screw provided. (Do not drill into
vehicle floor or bed.) Clean dirt and rustproofing
from area.
5. WARNING
Complete the installation per the electric brake
control manufacturer's instructions and mount
the unit as directed. Perform test procedures
as instructed.
NOTE
Vehicles not equipped with OEM trailer
tow package, may require fuses and relays
to complete output and battery feed circuits
(sold separately). Consult owners manual
for locations.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
Max. 3 AXLES: 6 BRAKES (18 amps)
Read vehicle's owners manual & instruction
sheet for additional information.