Fermax DUOX CITYLINE 1-2L Guía Rápida De Programación página 2

DUO DUO DUO DUO DUOX CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L
DUOX CITYLINE KIT 1-2L DUO DUO DUO DUO X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L
QUICK PROGRAMMING GUIDE
1. CONFIGURE AS MASTER PANEL
The programming is always done from the MASTER panel and there can only be one in
the complete installation.
Configuring the master panel: Press the SW1 button 3 times quickly, it is activated as
a MASTER panel and a confirmation tone sounds (beep-beep).
2. PROGRAMMING THE TELEPHONE
1
Programming Button
1. With the telephone connected, press the programming button (you will hear a beep).
Upon releasing it, you will hear the entrance into programming.
2. Press the call-to-residence button. A programming confirmation is produced.
* The telephone will not function until it has been programmed.
3. DEACTIVATE MASTER MODE ON THE PANEL
Once having completed the terminal's configuration, deactivate the MASTER panel to
avoid accidentally reprogramming terminals.
Deactivating the master panel: Press the SW1 3 times consecutively fast, and it will
deactivate the panel as MASTER. A deactivation tone sounds (beep-bop).
4. ENCODING PANELS
Whenever there are more than one panel (to a block) you must program the panel
number, but for this you need key 7439.
5 way cable
PUT
CN1
NTRITT
CN1
Connecting the keypad:
a) With the disconnected power, use the 5 way cable to connect the keypad as shown in
the diagram.
b) Reconnect the power supply. Now you can program the required parameters with the
keypad.
c) Before performing the operation to disconnect the keypad, remove the power.
2
5

A
< 2,5 min
CN1
AMPLIFICADOR
DUOX
CN1 AMPLIFIER
CN9
A
AUDIO
B
C
CN1 PACK EXTENSION
D
SW1 E
DL2 F
DL2 LED
IDIOMA
LANGUAGE
SW1 PROG
CN9 TAMPER
ONE
EXIT
TO
ONE BUS 18Vdc
CN2 CN3 P2 B B C NO NC BS - S + GND P1
+12
NC VERSION :
C
NO
ENTRADA/INPUT
CN1
ARRIVÉE/EINTRITT
CN1
1 2 3
MÓDULO TECLADO
KEYPAD MODULE
MODULE CLAVIER
UP TASTATURMODUL 4 5 6
7 8 9
A 0 B
CN2
SALIDA/OUTPUT
SORTIE/AUSGANG
ENGLISH
DUO DUOX CITYLINE KIT 1-2L DUO X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L
DUOX CITYLINE KIT 1-2L DUO DUO DUO DUO DUO DUO X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L X CITYLINE KIT 1-2L
The entry panel's parameters can be programmed on the keypad.
1.1 Access programming: A + 4444 (default code).
If the code is correct, a confirmation tone sounds (beep-beep).
1.2 Configuring the different parameters
The configuration of a parameter is done by entering: two digits of its position, and a
beep is heard and the desired value (1,2,3 or 4 digits relative to the parameter function).
If the value is correct, a confirmation tone sounds (beep-beep) and the new value is
saved. If not correct you will hear the error sound (beep-bop).
In order to exit the programming press 'A' when we are entering the menu's parameter
number. You can also exit by waiting 60 seconds without pressing any key.
Configuration of a parameter:
A + access code for programming + position + possible values
PROGRAM THE PANEL NUMBER,
Position Adjustments Parameter Possible Values [default]
06 Panel No. (PL)
Configuration of a panel number:
A + 4444 + 06 + 0-9
Example:
•
Change panel number 2:
A 4444 (beep-beep) 06 (beep) 2 (beep-beep)
If your installation is characterised by having General Inputs, Interior Blocks and/or
Sub-blocks, and must also program:
Position Adjustments Parameter Possible Values [default]
Panel type 0:
03
Sub-Block (SB)
[1]:
Block (BK)
2:
General Entrance (EG)
04
Block no. (BK) 00-99
[00]
00-99
05 Sub-Block no. (BS)
[00]
We recommend filling in the amplifier's sticker once each panel is programmed.
Examples:
General Entrance and Block 1 and panel number 2
panel number 3
TYPE Nº TYPE
X
EG EG
BK X BK
BK
SB SB
3
Nº PL Nº PL
5. RESET TO DEFAULT VALUES (if necessary)
A 4444 (beep-beep) 13 (beep) 1 (beep-beep)
Comments
0-9 [0] Panel number
TYPE Nº
EG
BK
BK
SB
2
Nº PL
Comments
Configuration of the panel
type
Block number the panel
belongs to
Sub-Block number the
panel belongs to
Sub- block 2 and panel
number 3, belonging to
block 1
Nº
TYPE Nº
01 EG
BK
BK
02 BK
X SB
01
2
3
Nº PL