Usb Power Port; Care And Maintenance - BLACK&DECKER PPRH5B Manual De Instrucciones

3. Switch on the appliance and operate as usual.
4. Periodically check the unit's battery status by pressing the battery power level button. (Two red
and one green battery status indicator lights indicate a full battery. Only one red battery status
indicator lights indicates that the unit needs to be recharged.)

uSB POWER PORT

The USB power port is under the same protective cover as the 12 volt DC outlet at the left hand side
of the front panel (refer to the Features section to locate).
1. Push the USB Power Button to turn the USB Port on and the USB power indicator will light.
2. Lift up the cover of the USB Charging Port.
3. Plug the USB-powered device into the USB Charging Port and operate normally.
4. Periodically check the unit's battery status by pressing the battery power level button. (Two red
and one green battery status indicator lights indicate a full battery. Only one red battery status
indicator lights indicates that the unit needs to be recharged.)
Notes:
This unit' s USB Power Port does not support data communication. It only provides 5 volts/500mA DC power to an external USB-
powered device.
Make sure the USB Power Button is in the off position when the unit is being recharged or stored.
Some household USB-powered electronics will not operate with this unit.
AREA LIGHT
The built-in 3-LeD area light located on the back of the unit is controlled by the area light on/off
button on the front panel (refer to the Features section to locate). Press the area light on/off button
once to turn the light on. Press the area light on/off button again to turn the area light off. Make sure
the area light and the unit are turned off when the unit is being recharged or stored.
Periodically check the unit's battery status by pressing the battery power level button. (Two red and
one green battery status indicator lights indicate a full battery. Only one red battery status indicator
lights indicates that the unit needs to be recharged.)
PORTABLE cOMPRESSOR
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and
recreational inflatables. The compressor hose with connector (chuck) is stored in the compressor
hose storage conpartment. The compressor on/off switch is located on the front panel of the unit to
the right of the air pressure gage (refer to the Features section to locate). The compressor can operate
long enough to fill up to 3 average sized tires before the battery must be recharged.
The compressor may be used by removing the air hose from the storage compartment and, if
required, fitting an appropriate nozzle to the air hose. Return hose to the storage compartment after
use.
WARNING: TO REDUCE THE RISK OF INJURy OR PROPERTy DAmAGE: FOllOW All SAFETy
INSTRUCTIONS FOUND IN THE "SPECIFIC SAFETy INSTRUCTIONS FOR COmPRESSORS" SECTION
OF THIS INSTRUCTION mANUAl.
CAUTION: TO REDUCE THE RISK OF PROPERTy DAmAGE:
Do not operate compressor continuously for extended periods of time (approximately 10 minutes,
depending on ambient temperatures), as it may overheat. In such event, compressor will automatically
shut down. Immediately press the compressor on/off button to turn the compressor off. Restart after
a cooling down period of approximately 30 minutes.
Inflating Tires or Products With Valve Stems
1. Place connector (chuck) on valve stem.
2. ensure connector is pushed on to valve stem as far as possible before closing thumb latch.
3. Make sure latch is secure.
4. Turn on the compressor power switch.
5. Check pressure with the pressure gage.
6. When desired pressure is reached, open thumb latch and remove connector from valve stem.
7. Turn off compressor power switch.
8. Allow unit to cool before storing away.
9. Store compressor hose and connector (chuck) in storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate nozzle, located on the inside back cover.
2. Insert appropriate adapter (i.e. needle) into connector (chuck) and close thumb latch.
3. Insert adapter (i.e., needle) into item to inflate to appropriate pressure.
4. Turn on the compressor power switch — inflate to desired pressure or fullness.
ImPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-
inflate.
5. Remove adapter.
6. Switch the Compressor Power Switch off.
7. Allow unit to cool before storing away.
8. Store compressor hose and connector (chuck) in storage compartment.
TROuBLESHOOTING
Unit will not charge
• Make sure the inverter power switch is in the off position.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning
AC outlet.
• Make sure the 12 volt DC charger is properly connected to both the unit and a functioning DC
power source.
Unit fails to jump-start
• Make sure unit's jump-starter power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
120 volt AC outlet will not power appliance
• Make sure the inverter power switch is in the on position.
• Make sure you have followed all the steps in the 120 AC portable power supply instructions
carefully.
• Refer to the important notes included in that section that explain common problems and solutions.
• Check that unit has a full charge. Recharge unit if necessary.
12 volt DC accessory outlet will not power appliance
• Make sure the the appliance does not draw more than 5 amps.
• Check that unit has a full charge. Recharge unit if necessary.
USB power port will not power appliance
• Make sure the USB power button is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
lED area light does not come on
• Make sure the area light on/off button is in the on position
• Check that unit has a full charge. Recharge unit if necessary.
Portable Compressor will not inflate
• Make sure the compressor power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure connector (chuck) is pushed to valve stem and thumb latch is closed when attempting to
inflate tires; or nozzle (adapter) is securely inserted into connector (chuck) on all other inflatables.
• The compressor may be overheated. Press the compressor on/off button to turn the compressor off.
Restart after a cooling down period of approximately 30 minutes.

cARE AND MAINTENANcE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When
the unit is not in use, we recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a
soft cloth moistened with a mild solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and
wires. Contact manufacturer to replace any components that have become worn or broken.
or