National Tree Company Dual Color Instrucciones De Seguridad Importantes

CAUTION IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use seasonal products outdoors unless
marked suitable for indoor and outdoor use.
When products are used in outdoor applications,
connect the product to a Ground Fault Circuit
Interrupter (GFCI) outlet. If one is not provided,
contact a qualified electrician for proper installation.
• This seasonal use product is not intended for
permanent installation or use.
• Do not mount or place near gas or electric
heaters, fireplaces, candles or other similar
sources of heat.
• Do not secure the wiring of the product with
staples or nails, or place on sharp hooks or nails.
Shaping
The product is shipped from the factory with the
branch tips compressed to the center. Each branch
tip must be shaped to its proper position to give the
Dual Color ®
Operating Instructions
(if equipped)
The hand switch operates the
functions of the lights. There are 10
functions, each one is activated with
the press of the foot switch. Functions
occur in the following order:
Steady warm white; twinkle warm
white; steady multicolor; twinkle
multicolor; steady pastel; fading warm
white to multicolor; random fading;
fading warm white; fading multicolor;
flashing warm white to multicolor.
Light functions always follow this
sequence.
Unlit / Pre-Lit Plug-In Decor Items
• Unplug the product when leaving the house, when
retiring for the night, or if left unattended.
• Do not let lamps rest on the supply cord or any wire.
• CAUTION: This is an electrical product – not a toy!
To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or
placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from
cord, wire or light string.
• Do not close doors or windows on the product or
extension cords as this may damage the wire
insulation.
product a natural look. This will also bring the piece
to its advertised dimension. The care and attention
given to this final process will result in a genuinely
Bulb Replacement
1. Unplug light string from power source.
2. Pull up on the Base Lock™ unlatching
the bulb from the bulb
socket. Gently pull the bulb
straight out (Figure 1).
3. Before inserting the new bulb
into socket, make sure that
the two wires on either side
of the the bulb base are straight up and
flush with the base (diagram at right).
4. Carefully insert new bulb into socket
and push down Base Lock until it snaps
into place (Figure 2).
LED Bulbs (Figure 3)
1. Unplug light string from power source.
2. Pull up on the Base Lock™ unlatching
the bulb from the bulb socket. Gently
pull the bulb straight out.
3. Carefully insert new bulb into socket
(bulb is keyed and only goes in one
way) and push down Base Lock until it
snaps into place.
SAVE THESE INSTRUCTIONS
2 Commerce Drive, Cranford, NJ 07016 www.nationaltree.com
• Never operate this product if the power cord or
plug is damaged.
• Use only manufacturer specified replacement bulbs.
• Read and follow all instructions that are on the
product or provided with the product.
USE AND CARE INSTRUCTIONS
• When storing the product, carefully remove the
product from wherever it is placed, avoiding any
undue strain or stress on the product conductors,
connections, and wires.
• When not in use, store neatly in a cool, dry
location protected from sunlight.
beautiful and appealing holiday decoration. Shaping
is done by gently grasping the branch tips and
spreading them out away from the center.
NOTE: Fuse failure is sometimes a reason
for non-functioning light strings. The fuses
are found in the light string plug. If one is
burnt out, replace it with a spare fuse
included in the accessories bag.
Fig. 1
Fuse Replacement
1. Unplug light string from power source.
2. Slide the fuse access cover away from
cord side (in direction of arrow, Figure 4)
exposing fuses.
Fig. 2
3. Remove fuses from compartment and
examine. Replace burnt out fuse with
Fig. 3
new one.
4. Close fuse compartment by sliding
access cover back in towards cord side
of plug (Figure 5).
Fig. 4 Fig. 5
Printed in China US-2-19