Publicidad
Finger Guard Cabinet & Drawer Latches
Parts & Terms Used
A
Latch
B
Catch
C
Screws (4 per lock)
D
Template (not shown)
A
Tools needed:
Phillips head screwdriver
1/16" drill bit (for predrilling holes)
"Finger Guard" para armarios y cajones
Piezas y términos utilizados
A
Pestillo
B
Enganche
B
C
Tornillos (4 por traba)
D
Plantilla (no se muestra)
C
Herramientas necesarias:
Destornillador Phillips
Taladro de 1/16" (para preparar los orificios)
Carefully cut template at the
Corte cuidadosamente la
To Install
Catch:
1
Line up catch to the front edge of the cabinet
opening.
2
Mark the hole locations and the outer edges of
the catch on the cabinet opening (Figure 1).
3
Predrill holes with a 1/16" (1.5mm) drill bit.
4
Secure catch tightly with screws.
Latch:
1
Locate the template and punch out the two holes X .
2
Line the template up with the catch so that the
dotted line is flush with the front edge of cabinet
opening. Tape template to cabinet (Figure 2).
3
Close the cabinet door/drawer and mark the outer
edges of the template on the cabinet door/drawer
and top edge on the template (Figure 3). Remove
the template.
4
Line the template up between the two marked
edges on the cabinet door/drawer with the marked
lines on the top edge of the cabinet door/drawer
and tape (Figure 4).
5
Mark the template hole locations on the cabinet
door/drawer. Remove the template and predrill
holes with a 1/16" (1.5mm) drill bit.
6
Secure latch tightly with screws.
NOTE: Cabinet door/drawer should not open more
than 2" (5.08cm).
To Use
1
1
When cabinet drawer/door is opened
the latch will engage the catch. The
cabinet drawer/door will remain in
a locked position until the latch is
released. Press down on latch with
finger to open.
NOTE: Normal use of product may
show discoloration of plastic at flex
points, but it does not affect safety or
function.
Latch may be difficult to access if used
on a top drawer that has a countertop
with a 1" overhang. If latch is difficult
to access, insert a rounded object to
depress latch.
To Clean
Wipe clean. Keep lock dry.
Para instalar
1
Enganche:
1
Alinee el enganche hasta el borde delantero de la
abertura del armario.
2
Marque las ubicaciones de los agujeros y los bordes
exteriores del enganche en la abertura del armario
(Figura 1).
3
Perfore los orificios con una broca de 1/16" (1.5 mm).
4
Fije firmemente el enganche con los tornillos.
2
Pestillo:
1
Localizar la plantilla y perfore los dos agujeros X .
eni ng
ine t op
2
of cab
edg e
eni ng
nin g
Fro nt
ine t op
Haga una línea en la plantilla con el enganche, de
ine t ope
edg e
of cab
of cab
edg e
Fro nt
Fro nt
manera que la línea punteada esté a nivel con el
borde delantero de la abertura del armario. Fije la
plantilla al armario con la cinta adhesiva (Figura 2).
3
Cierre la puerta/cajón del armario y marque los
3
bordes exteriores de la plantilla en la puerta/cajón
del armario y en el borde superior de la plantilla
1. Line up catch to the front edge of
1. Line up catch to the front edge of
1. Line up catch to the front edge of
the door/drawer opening.
(Figura 3). Quite la plantilla.
the door/drawer opening.
the door/drawer opening.
2. Mark the hole locations.
2. Mark the hole locations.
2. Mark the hole locations.
3. Cut out installation template from
3. Cut out installation template from
3. Cut out installation template from
instructions.
instructions.
instructions.
4. Punch out hole locations.
4. Punch out hole locations.
4. Punch out hole locations.
eni ng
5. Tape template to cabinet lining
ine t op
nin g
5. Tape template to cabinet lining
5. Tape template to cabinet lining
ine t ope
eni ng
edg e
of cab
of cab
ine t op
edg e
of cab
up dotted line with top edge of
Fro nt
Fro nt
edg e
4
up dotted line with top edge of
up dotted line with top edge of
Fro nt
cabinet opening.
cabinet opening.
Haga una línea en la plantilla entre los dos bordes
cabinet opening.
6. Close cabinet door/drawer.
6. Close cabinet door/drawer.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
7. Mark top edge of door/drawer on
marcados en la puerta/cajón del armario con las
7. Mark top edge of door/drawer on
the template. Also mark the width
the template. Also mark the width
the template. Also mark the width
of the template on the door/drawer.
of the template on the door/drawer.
of the template on the door/drawer.
líneas marcadas en el borde superior de la puerta/
8. Open door/drawer. Remove
8. Open door/drawer. Remove
8. Open door/drawer. Remove
template from base of cabient and
template from base of cabient and
cajón del armario y fije con cinta adhesiva (Figura 4).
template from base of cabient and
retape onto the inside of the
retape onto the inside of the
retape onto the inside of the
door/drawer.
door/drawer.
door/drawer.
9. Position the template onto the
9. Position the template onto the
9. Position the template onto the
inside of the door/drawer lining up
inside of the door/drawer lining up
inside of the door/drawer lining up
5
the pencil marks.
4
the pencil marks.
the pencil marks.
Marque las ubicaciones de los orificios de la plantilla
10. Mark hole locations.
10. Mark hole locations.
10. Mark hole locations.
11. Predrill holes with X" drill bit.
11. Predrill holes with X" drill bit.
11. Predrill holes with X" drill bit.
en la puerta/cajón del armario. Quite la plantilla y
perfore los orificios con una broca de 1/16" (1.5 mm).
6
Fije el pestillo firmemente con tornillos.
nin g
ine t ope
eni ng
of cab
ine t op
eni ng
edg e
of cab
ine t op
NOTA: No se tendría que abrir la puerta/cajón del
Fro nt
edg e
of cab
Fro nt
edg e
Fro nt
armario más de 2" (5,08 cm).
Para Usar
1
2
Cuando se abre la puerta o el cajón
del armario, el pestillo se agarra al
enganche. La puerta o el cajón se
quedará bloqueada/o hasta que se
suelte el pestillo. Presione el pestillo con
el dedo para abrir.
NOTA: El uso normal del producto
pueden mostrar decoloración del
plástico en los puntos de flexión, pero
que no afecta a su seguridad o función.
El pestillo puede ser de difícil acceso si
se utiliza en un cajón superior que tiene
una encimera con un 1'' que sobresale. Si
el pestillo es de difícil acceso, inserte un
objeto redondo para apretar el pestillo.
Para limpiar
Limpie con un paño. Mantenga la traba seca.
Publicidad
