Publicidad
Idiomas disponibles
Idiomas disponibles
Operating
instructions
Always observe the oper-
ating instructions and
„Important operating
notes" prior to starting!
The vehicle owner is respon-
sible for correct operation of
the appliance.
Control panel
with thermostat
Ultraheat
c
b
2000
a
b
500
b
1000
230 V ~
a = Rotary switch „Off"
b = Rotary switch „On"
power settings:
500 - 1000 - 2000 W
c = Rotary control knob for
room temperature (illumi-
nated by green indicator
lamp „operation")
Switching on
Before switching on,
ensure that the fuse
protection for the power sup-
ply of the camp site is suffi-
cient for the selected power
setting (b) (see Technical
Data).
1. To switch on, turn the ro-
tary switch to the desired
output level (b).
2. Set rotary control knob (c)
to the desired room tempera-
ture.
The thermostat setting on the
control panel (1 - 9) must be
determined individually de-
pending on the heating re-
quirement and the type of
vehicle.
To ensure even and rapid
warm air distribution as well
as lower surface tempera-
tures on the heating unit, we
recommend that you operate
the heater with a running
Trumavent warm air system.
Switching off
Switch the heating system
off at the rotary switch (a).
All manuals and user guides at all-guides.com
Maintenance
In the event of a fault contact
the Truma Service outlet in
the first instance (see page 16).
Caution: Despite
careful manufacture,
the heating system
may contain sharp-
edged components, and pro-
tective gloves should always
be worn when carrying out
any maintenance or cleaning
work.
Removing
the Heater Cover
Pull the cover forward at the
top, lift up the retaining
springs and fold out cover
forwards. (If space is limited,
lift the cover upwards and
forwards, lift until the cover is
released, then remove it.)
Then fit the panelling at the
side so that no connecting
cables (e.g. for the warm air
fan) have to be disconnected.
In order to fit the panelling,
place it in the lower retaining
clips (I) and engage the pan-
elling at the top.
Cleaning
(only when the unit
is switched off!)
It is advisable to remove dust
that has collected at the heat-
ing elements and the fan
wheel of the Trumavent
warm air system annually be-
fore the start of the heating
season. Carefully clean the
fan wheel with a paintbrush
or small brush.
Manufacturer's terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions in
the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
- for parts subject to wear
and in cases of natural wear
and tear,
- as a result of not original
Truma parts being used in
the appliance,
- as a consequence of failure
to respect Truma instruc-
tions for installation and
use,
- as a consequence of im-
proper handling,
- as a consequence of im-
proper transport packing,
not arranged by Truma.
2. Scope of warranty
The warranty is valid for mal-
functions as stated under
item 1, which occur within
24 months after conclusion
of the purchase agreement
between the seller and the fi-
nal consumer. The manufac-
turers will make good such
defects by subsequent fulfil-
ment, i.e. at their discretion
either by repair or replace-
ment. In the event of manu-
facturers providing service
under warranty, the term of
the warranty shall not re-
commence anew with regard
to the repaired or replaced
parts; rather, the old warranty
period shall continue to run.
More extensive claims, in
particular claims for compen-
satory damages by pur-
chasers or third parties, shall
be excluded. This does not
affect the rules of the product
liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty - in particular
transportation costs, travel-
ling expenses, job and mater-
ial costs, as long as the ser-
vice is carried out in Ger-
many. The warranty does not
cover customer service work
in other countries.
Additional costs based on
complicated removal and in-
stallation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The manufacturer's address
is: Truma Gerätetechnik
GmbH & Co. KG, Wernher-
von-Braun Strasse 12,
D-85640 Putzbrunn. In Ger-
many, always notify the
Truma service centre if prob-
lems are encountered; in oth-
er countries the relevant ser-
vice partners should be con-
tacted (see list of addresses).
Any complaints are to be de-
scribed in detail. In addition,
the properly completed guar-
antee certificate is to be pre-
sented, or the factory number
of the unit and the date of
purchase given.
In order for the manufactur-
ers to be able to determine
whether an incident subject
to guarantee has occurred,
the end user must, at his own
risk, bring the device to the
manufacturers or send it to
them.
In instances of the device
being sent to the works, dis-
patch is to be effected by
freight transport. In cases
under guarantee, the works
shall bear the transport costs
or the costs of delivery and
return. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.
5
Publicidad
