Campbell Hausfeld MP516803 Instrucciones De Operacion Y Lista De Partes página 2

Mini General Purpose Filter
Installation
(Continued)
3. Remove plug from plastic bag.
Install securely in the port opposite
the gauge. (See Figure 3.) Plug has
thread seal already applied.
4. Securely mount the filter /regulator
in a vertical position as close as pos-
sible to air tool connection.
5. Verify that the "IN" and "OUT"
markings match the air flow
direction. (See Figure 2.)
6. Install the unit with the same pipe
size as the piping in use. Avoid
using unnecessary fittings,
couplings, etc., that restrict airflow.
7. Connect the air supply to the inlet
port.
Operation
regulator adjusting knob is unlocked
when adjusting pressure. The
regulator will be damaged if the knob
is turned in the locked position.
1. Before pressurizing system, make
certain the bowl is securely screwed
into the filter body.
MATERIALS THAT ATTACK POLYCARBONATE PLASTIC (PARTIAL LISTING)
Acetaldehyde
Acetic acid (concentrated)
Acetone
Acrylonitrile
Ammonia
Ammonium flouride
Ammonium hydroxide
Ammonium sulfide
Anaerobic adhesives & sealants
Antifreeze
Benzene
Benzoic acid
Benzyl alcohol
Brake fluids
Bromobenzene
Butyric acid
Carbolic acid
www.chpower.com
2. Unlock the regulator adjusting
knob by pulling knob away from
the regulator.
3. Turn the regulator adjusting knob
counterclockwise until no load is on
the regulating spring.
4. Turn on the air pressure supply and
turn the adjusting knob clockwise
until the desired outlet pressure is
reached. Push the regulator
adjusting knob toward the
regulator to lock in desired
pressure.
Maintenance
Release all pressure before
attempting to install, service,
relocate or perform any
maintenance on the air system.
Ensure
Personal injury and/or property
the
damage could occur.
depressurize the unit before removing
the bowl. Personal injury and/or
property damage could occur. If bowl
is difficult to remove, it may be under
pressure.
Carbon disulfide
Carbon tetrachloride
Caustic potash solution
Caustic soda solution
Chlorobenzene
Chloroform
Cresol
Cyclohexanol
Cylohexanone
Cyclohexene
Dimethyl formamide
Dioxane
Ethane tetrachloride
Ethyl acetate
Ethyl ether
Ethylamine
Ethylene chlorohydrin
FILTER
1. Inspect for cracked, damaged or
2. Replace or clean filter element
3. Drain bowls at least once per work
4. Before placing the unit in service,
Technical Service
For information regarding the
operation or repair of this product,
please call 1-800-543-6400.
Always
Ethylene dichloride
Ethylene glycol
Formic acid (concentrated)
Freon (refrig. & propell.)
Gasoline (high aromatic)
Hydrazine
Hydrochloric acid (concentrated)
Lacquer thinner
Methyl alcohol
Methylene chloride
Methylene salicylate
Mike of lime (CaOH)
Nitric acid (concentrated)
Nitrobenzene
Nitrocellulose lacquer
Phenol
2
Model MP516803
deteriorated seals and bowls. If
damage is present, the unit must be
replaced. Wipe bowls with a soft,
dry cloth to clean.
periodically. Remove the filter
element and tap filter on a hard
surface or use an air gun to blow
off residual dirt.
shift. To avoid spray or splatter,
cover bottom of filter with a cloth
and push the manual drain.
make sure the bowl is reinstalled
and securely locked in place.
Phosphorous hydroxy chloride
Phosphorous trichloride
Phopionic acid
Pyridine
Sodium hydroxide
Sodium sulfide
Styrene
Sulfuric acid (concentrated)
Sulphural chloride
Tetrahydronaphthalene
Tiophene
Toluene
Turpentine
Xylene
Perchlorethylene and others