Measure The Installation - Broan EVOLUTION 2 QP2 Serie Manual Del Usuario

PREPARE HOOD LOCATION
5 Use the proper diagram below, for placement of ductwork
and electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole.
HOOD MOUNTING SCREWS (5)
5 /
11 " (30" hood)
8
5 /
14 " (36" hood)
8
5 /
17 " (42" hood)
8
CABINET FRONT
CABINET
BOTTOM
5¼"
VERTICAL DUCT
4½" ACCESS HOLE
¾"
WOOD SHIMS
CENTER
(recessed-bottom
LINE
cabinets only)
WOOD SHIMS
(recessed-bottom
cabinets only)
CABINET FRONT
4" HORIZONTAL DUCT
ACCESS HOLE
CABINET
BOTTOM
5¼"
5 /
11 " (30" hood)
8
5 /
14 " (36" hood)
8
5 /
17 " (42" hood)
8
HOOD
MOUNTING
CENTER
SCREWS (5)
HOOD MOUNTING SCREWS (5)
5 /
11 " (30" hood)
8
5 /
14 " (36" hood)
8
5 /
17 " (42" hood)
8
8" DIA.
HOLE
7-IN. ROUND 7-IN. ROUND
DUCT DUCT
ACCESS ACCESS
4 / " HOLE HOLE
5
8
*
Note the extra wood shim and mounting screw near the
cabinet front, on the cabinet center line.
3¼" X 10"
VERTICAL DUCTING
5 /
11 " (30" hood)
8
5 /
14 " (36" hood)
8
5 /
17 " (42" hood)
8
*
7 /
6 "
8
5¼"
10
11"
1 /
2 "
8
5 /
2
8
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)
3¼" X 10"
HORIZONTAL DUCTING
1 / "
3
8
/ "
3
8
*
5¼"
6 / "
7
8
5 /
11 " (30" hood)
8
5 /
14 " (36" hood)
8
5 /
17 " (42" hood)
8
ELECTRICAL
ACCESS HOLE
LINE
(in wall)
7-IN. ROUND
DUCTING
5 /
11 " (30" hood)
8
5 /
14 " (36" hood)
8
5 /
17 " (42" hood)
8
*
6 / "
7
8
10
11"
2 / "
1
8
2 /
5
8
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)

MEASURE THE INSTALLATION

SOFFIT
CABINET
7 /
"
24" - 30" ABOVE
8
COOKING SURFACE
"
6 The minimum hood distance above cooking surface
MUST NOT BE LESS than 24" (to top of hood).
A maximum of 30" above cooking surface is highly
recommended for best capture of cooking impurities.
Distances over 30" are at the installer's and user's
discretion; providing that the cabinet height permits.
CONTENTS
(2 - FOR 30" & 36" HOODS)
HALOGEN
BULBS
(3)
WIRE
NUTS
(9)
#8 X 1/4"
DUCT
/ "
7
8
CONNECTOR
SCREWS
"
ROOF CAP
3¼" X 10" or
7" ROUND DUCT
(For vertical
discharge)
HOOD HOOD
INCLUDED WITH THE HOOD:
GREASE
FILTERS
3 - FOR 42" HOODS)
(1) 7" ROUND
(4)
CONNECTOR
(1) PARTS BAG CONTAINING:
(1)
BULB
SUCTION
CUP TOOL
(5)
#10 X 5/8"
RD. HD.
MOUNTING
SCREWS
QP2 SERIES
Page 4
HOUSE WIRING
(Top or Back of hood)
WALL CAP
3¼" X 10" DUCT
(For horizontal discharge)
(1) 3¼" X 10"
DAMPER / DUCT
CONNECTOR
DUCT
(1)
NON-DUCT
DIVERTER
(2)
#8 X 5/16"
MACHINE
SCREWS
&
(2)
#8 WASHERS
FOR NON-DUCT
DIVERTER