Maintenance And Care; Customer Information; Limitation Of Liability; Maintenance And Repair - 3M ESPE Pentamix Lite Instrucciones De Uso

Seite 8 - 210 x 297 mm - 44000767093/02 - SCHWARZ - 13-072 (sr)
Malfunction Cause
The paste flows too The pastes are too
slowly or not at all cold, or sealing cap
of the base paste is
defective
The paste is extruded The drive shaft has
but the rotor in the tip not engaged the
does not rotate mixing tip, it is stuck
in its top position
The cartridge will not The plungers are not
fit into the unit fully retracted
The cartridge
receptacle is dirty
The unit does not The "Start" button
switch off is stuck
The plungers are Foil of a bag is
difficult to retract wedged between
the cartridge and
the plunger

7. Maintenance and Care

7.1 Replacement of the Plunger Discs
If damaged, the plunger discs must be replaced. Only original parts may
be used as replacements to insure safe operation.
Turn off the unit and disconnect the plug from the power source. Use
an Allen wrench to remove the screw in the center of the plunger disc.
Remove the disc and screw a new one into place (Fig. 21).
When changing the plunger discs, make sure you position them with the
correct alignment (see Fig. 21) to prevent damage to the foil bags.
7.2 Care
Clean all components with a soft cloth and, if necessary, a mild cleaning
agent (e.g., dish-washing detergent). Solvents or abrasive cleaners may
not be used in any case, as they can damage the plastic components!
- Cleaning agents must not enter the unit!
To disinfect all components, spray the disinfectant on a towel and
use it to disinfect the unit. Do not spray the disinfectant directly on
the device.
- Disinfectant agents must not enter the unit!
- Dry residual disinfectants on the device with a soft and fluff-free
cloth, as they damage the plastic components.
If necessary, ask the manufacturer of the disinfectant if its constant use
will damage plastic surfaces.

7.3 Maintenance and Repair

No components inside the unit require servicing or repair by the user.
3M Deutschland GmbH will accept responsibility for the safety, reliability,
and correct function of the unit only if:
- Any modifications or repairs are carried out only by personnel
authorized to do so by 3M Deutschland GmbH;
8
- The electrical fittings in the room comply with all regulatory
Remedy
Allow the pastes to
- The unit is operated according to these Operating Instructions.
attain room temperature
(at least 18° C).
Plastic cartridges are subject to wear depending on the material and
Replace defective foil
frequency of use and are therefore not covered by the warranty for this
bag
unit. They should be regularly checked for signs of wear (e.g., fissures)
and replaced with new Penta cartridges for Pentamix Lite two years after
Remove the mixing tip.
initial operation at the very latest. The use of worn or defective cartridges
Turn the plungers
can have adverse effects on the evenness of the mixture, reducing the
several times up to
quality of the impression.
their upper limit,
thus regaining axial
moveability. Attach

8. Customer Information

new mixing tip
Turn the plungers up
to their limit by turning
No person is authorized to provide any information that deviates from the
the adjustment knob
information provided in this instruction sheet.
clockwise and arresting
it. Check the plunger
8.1 Warranty
discs for damage
3M Deutschland GmbH warrants this product to be free from defects
Clean the cartridge
in material and manufacture. 3M Deutschland GmbH MAKES NO
receptacle
OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
Press the "Start" button
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. User is
again or unplug the
responsible for determining the suitability of the product for user's
unit and release the
application. If this product is defective within the warranty period, your
"Start" button
exclusive remedy and 3M Deutschland GmbH's sole obligation shall be
repair or replacement of the 3M Deutschland GmbH product.
Retract plunger
against the resistance,
but avoid damage of

8.2 Limitation of Liability

plunger discs
Except where prohibited by law, 3M Deutschland GmbH will not be liable
for any loss or damage arising from this product, whether direct, indirect,
special, incidental or consequential, regardless of the theory asserted,
including warranty, contract, negligence or strict liability.
Information valid as of August 2013
requirements;