Chicco Balloon Instrucciones De Uso página 13

BOOSTER CUSHION
10. The reducer cushion (D) - (DD) is ideal from birth and can be
removed according to needs. To fix it to the seat, place it on the
seat and slide the crotch strap through the hole (Fig. 13). Thread
the safety harness in the relative side slots of the reducer cushion
(Fig. 13 A). Fix the headrest to the seat, sliding the straps through
the slot and close it again using the velcro strap (Fig. 14).
TOYBAR
11. Fasten the toybar (E) to the frame inserting the lower ends in the
relevant fastening hole of the toybar (Fig. 15).
WARNING: Always check that the toybar is properly fastened
before every use. The toybar can be used in two different modes,
slightly lifting it from its seat and turning it to the desired position
(Fig. 16).
12. The toys can be fastened to the toybar inserting the belts in the
holes in the bar (Fig. 17).
WARNINGS ELECTRICAL PARTS
• To replace the batteries: loosen the screw on the battery compart-
ment cover with a screwdriver and open the cover. Then remove
the spent batteries and fit new ones, paying attention that the
poles are in the right direction (as shown on the product), close the
battery cover and tighten the screw. Repeat the same operation
for the Vibrating Box (Toybar 2 AA 1.5 Volt type batteries - Vibration
Box 1 LR20 1.5V battery).
• Batteries must only be fitted by an adult.
• Only use alkaline batteries of the same type or equivalent to the
type recommended for the correct function of this product (Toy-
bar 2 AA 1.5V batteries - Vibration Box 1 LR20 1.5V battery).
• Make sure the batteries are fitted with their poles in the right direction.
• Never mix new and old or different types of batteries.
• Always keep batteries and tools out of the reach of children.
• Do not short-circuit the power terminals.
• Always remove discharged batteries from the product to avoid any
possible liquid leaks that may damage it.
• Always remove the batteries if the product will not be used for a
long period of time.
• Remove the batteries from the toybar and vibrating box before
disposing of the product.
• Do not throw dead batteries in fire or leave them in the environ-
ment; they must be disposed of through waste sorting.
• If the batteries are leaking liquid, replace them immediately, mak-
ing sure to clean the battery compartment; thoroughly wash your
hands in the case of contact with the liquid.
• Always dispose of leaking batteries immediately: they can cause
burns or other types of injuries.
• Do not try to recharge non-rechargeable batteries: they may explode.
• The use of rechargeable batteries is not recommended as they
may reduce the toy's operability.
• If using rechargeable batteries, remove them from the toy before
recharging them.
• Do not leave the product outside under the rain; water infiltrations
will damage the electronic circuit.
• Rechargeable batteries must be charged only under adult supervision.
REMOVABLE SOUND TOY
The toybar is fitted with a sounds and lights panel that is activated
by pressing the buttons on the front section (Fig. F).
F1 : On button - volume
F2 : It plays soothing and relaxing tunes
F3 : It plays lullabies
F4 : It plays funny music
F5 : Voice recording button
F6 : Sound and music activation handle
F7 : Microphone - Led
For the voice recording activation, check that the sound toy is on.
Keep the F5 button pressed; as soon as the red LED flashes, the own
voice can be recorded, to stop recording release the button (the
LED will turn off ). The recording can have a maximum duration of
30 seconds.
To listen to the recording, press the button.
To record again, repeat the steps described above.
To obtain an optimal recording, it is recommended to keep a dis-
tance from the microphone (F7) of about 20 cm with a clear and
decisive tone of voice; it is important not to block the microphone
hole in order not to compromise the quality of your recording
The sound toy can be removed by pressing the button E1 (Fig. 18).
Once removed, the sound toy can be fastened to the bed frame us-
ing the strap (I) (Fig. 19). The strap has two slots to make it compat-
ible to most of the bed frames (Fig. 20).
WARNING: To prevent possible injury by entanglement, remove
this toy when the child starts trying to get up on its hands and knees
in a crawling position.
To refit the sound toy on the bar, slide it as indicated in Fig. 21 until
you hear it "CLICK" into place.
VIBRATION BOX
The vibration box (Fig. 22) is placed on the front seat support.
Turning the switch clockwise, the vibration starts, to turn it off, bring
the switch back to"0".
HOW TO REMOVE THE FABRIC COVER
It is possible to remove the seat cover and the booster cushion from the
reclined cradle to wash them.
13. Remove the booster cushion.
14. Remove the safety harness from the slots in the fabric and start to
remove the cover (Fig. 23). Release the 6 click buttons (Q) at the
side under the metal tubes, remove the cover on the vibrating box
(Fig. 24), then take off the fabric through the entire frame paying
attention not to damage it. To refit the cover, proceed in reverse
order, making sure that the lower fabric strap goes through the
adjustment joints of the backrest (Fig. 25) and the toybar support.
10/12 M, up to 18 Kg
(CHAIR USE)
• Age range intended for use: from
when your child starts walking and
is able to sit down and stand up by
himself (about 10/12 months, max.
18 kg).
• WARNING: Before using as a chair,
remove the safety harness (crotch
strap and waist belt) and position
them in the relevant spaces.
• WARNING: Never leave the child
unattended.
• Place only on flat and stable sur-
faces.
• Do not use the product as a chair in
rocker mode.
• The dimensions of the product are
80 x 43 x 32/62.
• WARNING: Check that the space
where the chair will be used is free
of objects or furniture that may ob-
struct the product or compromise
its correct use .
• Do not let your child stand up on
13