Dimplex DF2010-EU-E Guía De Instalación Y Uso página 5

Controls: See Fig. 2 & 3
Icon Display Function Description
Power /
A
-
Standby
Sleep
B
Timer
Flame Effect
Low
f1
Flame
High
f2
Flame
C
Demo
fP
Mode
-
Heat
Low
Heat
D
High
Heat
Cool
Blow
-
Temp
E
-
Down
Temp
F
-
User Modes:
Mode Name /Discription
Change Celsius ( C) to Fahrenheit (
0
Disable Heat Options
Enable Heat Options
Press Once to turn the product 'ON'.
Press a second time to put the product into 'STANDBY'
(When returning from 'STANDBY' mode the product will return to previous settings unless
the product has been plugged out, in which case it will reset to factory settings)
Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the 'SLEEP TIMER' displays.
(This icon is Green in Colour)
'FLAME EFFECT' button cycles the unit
HIGH FLAME, DEMO MODE and OFF.
This setting will run the flame effect at a low brighness level. (The display will show F1)
This setting will run the flame effect at a high brighness level. (The display will show F2)
This setting will slowly pulse the flame effect between low and high brightness. (The display
will show FP)
This will turn the flame effect off. If the heater is running, the display will activate and
Off remain active to read the set temperature and show if the product is on LOW HEAT/ HIGH
HEAT/COOL BLOW.
'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the floating display
see Fig.1.
When the flame effect is 'ON' the floating display will turn off after 5 seconds, however
if the heater is being used independantly of the flame effect. The low heat or high heat
icon will appear continuously in the floating display.
This setting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW
HEAT' icon and the letters 'LO' appearing in the display.
(This icon is Orange in Colour)
This icon in the floating display indicates 'HIGH HEAT' this setting will be indicated by the
'HIGH HEAT' icon and the letters 'HI' appearing in the display.
(This icon is Red in Colour)
This icon in the floating display indicates 'COOL BLOW' this setting will be indicated by
the 'COOL BLOW' icon and the letters 'CB' appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower 'OFF', no icon will be displayed in the floating display.
Off Note the blower will run for 10-20 seconds after being turned off this is to ensure the product
cools down safely.
Press multiple times to lower the heater temperature in 1
temperature that can be set 5
Note: Once you stop at your desired temperature this will flash 3 times, then the display
will show the room temperature as detected by the product. If the set temperature is
lower than the detected room temperature the heater will not activate.
Press multiple times to increase the heater temperature in 1
temperature that can be set 37
Up
Note: Once you stop at your desired temperature this will flash 3 times, then the display
will show the room temperature as detected by the product. If the set temperature is
lower than the detected room temperature the heater will not activate.
Action (Actions cannot be input by remote control)
F) Press both Temp+ (
0
heard and display flashes. (To revert back to Celsius repeat this action)
Hold both Heat (
the heater has been disabled the display will read "--" and beep.
Hold both Heat (
the heater has been sucessfully enabled the heater will beep and the show
the set temperature.
sequentially through the 4 setting, LOW FLAME,
0 C.
C.
0
) and Temp– ( ) on the unit and hold until beep is
) and Flame Effect (
) and Flame Effect ( ), on the unit, for 2 seconds. When
0 C increments. The lowest
0 C increments. The highest
), on the unit, for 2 seconds, when