Versaclean 108779 Manual Del Usuario página 3

CLEANING
7. Pretreat soiled area (optional). Apply spot cleaning
or other prespray solution directly and let it dwell on
cleaning surface per chemical label.
8. Rinse extraction. Rinse with plain water solution and
extract thoroughly.
9. Dry completely. Accelerate drying with warm air
temperatures and airmovers.
Cleaning Tips:
• Test surfaces first for colorfastness.
• Clean small sections at a time. If using prespray,
don't let it dry on surfaces.
• Don't over-wet. Always extract thoroughly.
OPERATION
10. Turn on Blower and Pump/Heater.
11. Wait for heated solution to reach hand tool, then
begin cleaning (see CLEANING above).
Empty/refill tanks
NOTICE: When cleaning solution is used up, 1) empty
recovery tank and 2) refill solution tank.
1. Empty recovery tank.
a) Switch off blower and heater.
b) With vacuum hose still attached, lift vacuum hose
vertically to drain any water in hose into recovery
tank.
c) Remove vacuum hose from recovery tank.
d) Release twist latch, slide recovery tank forward and
lift up. Keep vacuum inlet tipped upward to avoid
drips from the vacuum intake.
e) While holding the tank upright, remove tank cap
f) Pour into a suitable drain, such as a toilet or utility
sink.
2. Refill solution tank (see SETUP steps 3 and 4) when
emptying recovery tank or when no solution flows from
spray nozzle.
3. Resume cleaning.
MAINTENANCE
WARNING: Unplug machine before servicing.
Possibility of electrical shock.
WARNING: Interior components may be hot
after operation. Let unit cool completely
before servicing.
DAILY OR AFTER EACH USE
Rinse solution tank with clear water to ensure no
detergents or rinse agents remain in the tank.
122051C VERSATILE DEEP CLEANER 115V
Clean strainer cup and float ring. Remove solution
tank cover, lift out assemblies and rinse clean. Allow
assemblies to air dry before reinstallation.
Rinse recovery tank with clean water. Helps to prevent
damaging deposits and reduces the growth of odor-
causing bacteria.
Wipe exterior with damp cloth.
Reassemble unit and turn on blower motor ONLY
and run for 2 minutes to remove remaining moisture
from the blower.
Release water pressure with accessory tool spray
control lever, then disconnect vacuum hose and
solution hose. Coil for storage.
Coil power cord and secure with strap for transport
and storage.
AS NEEDED
To restore exterior shine, use an automotive vinyl
cleaner/protectant product.
CONTACT
Legend Brands
15180 Josh Wilson Road
Burlington, WA 98233
800-932-3030 service@CleanerLivingProducts.com
VDC.CleanerLivingProducts.com
SPECIFICATIONS
Model
Capacity
Vacuum lift
Solution spray pressure
Solution spray flow
Dimensions
(H × L × W)
Weight
Amps
Volts
Frequency
Power (full)
Operating range
Sound level
Construction
Power cord
3
108779
Solution tank: 2.5 gal. | 9.5 L
Recovery tank: 2.0 gal. | 7.6 L
4.5 in. | 114.3 mm Hg
58 PSI | 400 kPa
0.18 GPM | 0.68 LPM
22.4 × 26.0 ×11.1 in.
56.9 × 66.0 × 28.2 cm
34.6 lbs. | 15.7 kg (without hose and tool)
Pump: 0.5A Vacuum: 7.0A Heater: 6.0A
Total: 13.5A
115V
60 Hz
1.55 KW
33°F–100°F | 1°C–38°C
53 dB
Rotomolded polyethylene housing
25 ft. | 7.6 m
Legend Brands, Inc.