Publicidad
Enlaces rápidos
PO 4500007221, PO 4500007224
PO 4500007225, PO 4500007226
USE THIS ADDENDUM FOR STEP 5.
UTILISEZ CET ADDENDA POUR L'ÉTAPE 5.
UTILICE ESTE APÉNDICE PARA LA ETAPA 5.
- PRE-DRILL A HOLE AT THE DESIRED HEIGHT USING A 3/16" DRILL BIT,
MAKING SURE IT IS ALIGNED TO A STUD.
- PERCEZ AU PRÉALABLE UN TROU À LA HAUTEUR SOUHAITÉE À L'AIDE D'UNE
MÈCHE DE 3/16", EN S'ASSURANT QU'IL EST ALIGNÉ À UN MONTANT.
- PERFORAR CON ANTELACIÓN UN AGUJERO EN LA ALTURA DESEADA Y
UTILIZANDO UNA BROCA DE 3/16". ASEGURARSE ELLO ES ALINEADO A UN VIGA.
STUD
MONTANT
VIGA
Publicidad
Manuales relacionados para Tech Craft FLEX52W
Resumen de contenidos para Tech Craft FLEX52W
- Página 1 PO 4500007221, PO 4500007224 PO 4500007225, PO 4500007226 USE THIS ADDENDUM FOR STEP 5. UTILISEZ CET ADDENDA POUR L'ÉTAPE 5. UTILICE ESTE APÉNDICE PARA LA ETAPA 5. - PRE-DRILL A HOLE AT THE DESIRED HEIGHT USING A 3/16" DRILL BIT, MAKING SURE IT IS ALIGNED TO A STUD.
- Página 2 ATTENTION FLEX52W PO #4500007222 PO #4500007223 THE RECT. BRACKET HOOK NUMBER (IMC00077-BP) IMC0208-BP MUST BE LE NUMÉRO DU CROCHET D’ANCRAGE (IMC0077-BP) IMC0208-BP DOIT ÊTRE ON STEP 5, THE TEXT ON DRAWING “A” SHOULD BE : - PRE-DRILL A HOLE AT THE DESIRED HEIGHT USING A 3/16" DRILL BIT, MAKING SURE IT IS ALIGNED TO A STUD.
- Página 3 PAGES / PÁJINAS 8-9 PAGES / PÁJINAS 8-14 PAGES / PÁJINAS 3-7 Model/Modèle/Modelo FLEX52W IMPORTANT CUSTOMER SERVICE INFORMATION / IMPORTANT INFORMATION DE NOTRE SERVICE À LA CLIENTÈLE / INFORMACIÓN IMPORTANTE SOBRE SERVICIO AL CLIENTE INCLUIDA WARRANTY THIS ASSEMBLY INSTRUCTION IS REQUIRED TO VALIDATE THE AND FOR ANY REQUEST TO THE CUSTOMER SERVICE.
-
Página 4: Tools Required
No utilice detergente en polvo, ningun material abrasico ò solvente. FLEX52W PART No REV. PART NAME / NOM DE LA PIÈCE / NOMBRE DE LA PIEZA CLÉ... - Página 13 INSTALLATION : TECHCRAFT highly recommends that you use a qualified professional contractor to perform the entire installation. Do not use this product for any purpose other than that specified by TECHCRAFT. If you do not understand or comprehend these directions or have any doubts about the safety of the installation, please call a qualified contractor or contact TECHCRAFT at www.techcraft.net.
- Página 14 IF YOU WANT TO HANG YOUR TV ON THE WALL, FOLLOW THESE STEPS. SI VOUS DÉSIREZ INSTALLER VOTRE TÉLÉ AU MUR, SUIVRE CES ÉTAPES. Si usted quiere instalar su tele sobre la pared, seguir estas etapas. TOOL REQUIRED: Mallet, Power Drill, 3/16” drill bit, socket or wrench set, stud sensor, open wrench OUTILS REQUIS: Maillet, perceuse, mèche de 3/16”, jeu de clés à...
- Página 15 TOOL REQUIRED: Mallet, Power Drill, 1/2" masonry bit, socket or wrench set, open wrench OUTILS REQUIS: Maillet, perceuse, mèche à béton de 1/2", jeu de clés à douille ou jeu de douilles, clé ouverte HERRAMIENTAS NECESSARIAS: Mazo, perforadora mecánica, broca a hormigón de 1/2", juego de llaves mecánicas o casquillos, llave fija 1- Use the mounting frame as a template to mark six (6) holes on the wall.
- Página 16 WARNING: DO NOT LAY THE TV FACE DOWN ON THE GLASS, lean it up against a wall or other solid surface. Laying the TV down on the glass may cause permanent damages. Place the rect. bracket hooks (IMC0077-BP) vertically as close to center of the TV as possible before installation. Thread bolts with your hand into your TV back.