McCulloch ROB S400 Guía Rápida página 3

1. P L AC E M E N T O F A N D C O N N E C T I N G T H E C H A R G I N G S TAT I O N
See chapter Installation in the Operator's Manual
1. Place the charging station at a central position in the working area, with a lot of open space in front of the charging station
and on a relatively horizontal surface.
2. Connect the power supply's low voltage cable to the charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Press the ON/
OFF button to turn the product on.
2 . P L AC E M E N T O F T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
See chapter Installation in the Operator's Manual
1. Lay the boundary wire so that it forms a loop around the working area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight
angles.
3. C O N N E C T I N G T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
See chapter Installation.in the Operator's Manual
1. Fasten the guide wire in snap locks at the bottom of the charging station.
2. Open the connectors and lay the wire ends in the recesses on each connector.
3. Press the connectors together using a pair of pliers.
4. Cut off any surplus boundary wire. Cut 1 to 2 cm / 0,4 to 0,8" above the connectors.
5. Press the connectors onto the contact pins, marked L (left) and R (right), on the charging station. It is important that the
right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
6. Fasten the connector to the contact pin marked Guide on the charging station.
4 . C O N N E C T I N G T H E G U I D E W I R E T O T H E B O U N DA RY W I R E
See chapter Installation in the Operator's Manual
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together
with an adjustable pliers.
5. S TA R T I N G A N D S T O P PI N G
See chapter Operation in the Operator's Manual
STARTING
1. Open the hatch to the keypad.
2. Push the ON/OFF button. The display is lit up.
3. Use the up/down arrow buttons and the OK button to enter the PIN code. Close the hatch.
STOPPING
Press the STOP button.
6. A D J U S T I N G T H E R O B O T I C L AW N M O W E R T O S U I T T H E S I Z E O F YO U R
L AW N
See chapter Operation in the Operator's Manual
The mowing results depend on mowing time. Adjust the mowing time to suit your garden using the Schedule function. You
decide what times during the day the robotic lawnmower is to work. The robotic lawnmower mows about 40-42 m² / 430-452 sq.
ft. per hour and day. For example; if your garden consists of 300 m² / 3200 sq. ft. of grass, the robotic lawnmower should work
on average 7-7.5 hours per day.
7. M A I N T E N A N C E
See chapter Maintenance in the Operator's Manual
1. Turn off the product during all work on the product, such as cleaning or replacing the blades. Check that the indicator lamp
on the keypad is not lit.
2. Never use solvents for cleaning.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
QG_1140738_ROB_R400_R500_R600_201812.indd 3
E N
2018-12-18 11:20:30