Bushnell 98-0622/04-06 Manual Del Propietário página 3

englISh
Congratulations on selecting your new Bushnell Illuminated Red Dot Scope. This
scope has been specifically designed for use on shotguns, rifles and handguns. It is
constructed and assembled by highly skilled craftsmen to Bushnell's high quality
standards. The precision and craftsmanship with which this scope was built ensures
its performance under demanding conditions. This scope will provide the shooting
accuracy and repeatability which have made Bushnell legendary.
The following photographs are a guide to the nomenclature and location of the
parts mentioned throughout this text.
eYe guaRd eleVatIon
adjuStment
4
wIndage adjuStment BodY tuBe
NOTE: POSITION OF CONTROLS AND NUMBER OF EXTENSION
TUBES MAY VARY BY MODEL.
focuSIng
4
This scope has a magnification of one power (1x). Therefore, no focusing is re-
quired. The clarity and resolutions will be as sharp and defined as can be seen with
your eyes.
mountIng
The base and rings (mount) can affect your shotgun, rifle or handgun shooting
performance and accuracy. If your scope is mounted improperly, you may never
achieve the best accuracy from your firearm. You may choose to mount your own
scope or opt to have a gunsmith do it for you.
Your scope should be mounted as low on the firearm as possible. This will keep
4
your face or cheek close to the line of sight and will also keep the scope close to the
2
Trophy Red Dot RS 6LIM.indd 4-5
on/off SwItch, extenSIon tuBe
IntenSItY contRol,
BatteRY coVeR
5 5
oBjectIVe tRIm RIng
polaRIZIng
(not necessary to remove
fIlteR
on 1x30 trophy model)
5 5
5 5
center line of the bore – both factors will help you attain optimum accuracy. When
properly mounted, the scope will be as near center as possible, allowing for a full
range of elevation and windage adjustments.
4 5
The Bushnell Illuminated Red Dot Scope comes complete with a set of mounting
rings. These rings are designed to fit any standard dovetail, B-Square or Weaver
style base. Carefully follow the instructions packed with the base you have selected.
Before tightening the mount rings, rotate the scope until the windage adjustment
is perpendicular to the firearm's bore and the elevation adjustment is on top. Next,
tighten the mounting ring screws as tight as possible.
extenSIon tuBe
4 5
NOTE: This scope has been designed to be as compact as possible for handgun use.
If you are mounting your scope on a shotgun or other firearm, you may require a
longer mounting length. To increase your mounting length, remove the objective
trim ring. Thread the extension tube onto the body tube and thread the objective
4 5
trim ring into the extension tube. You should mount your scope so that there is at
least three inches of clearance between the scope and your eye when in the shoot-
ing position.
BoRe SIghtIng
Bore sighting is a good preliminary procedure in achieving proper alignment of
your scope to the firearm. It is best performed with a Bushnell Bore Sighter. If
not available, it can be done adequately in the following manner: Sight through
the gun barrel at a 100 yard target. Then sight through your scope and bring the
red dot to the same point on the target. The red dot is illuminated by turning on
the on/off switch. Rotate the knob until you have achieved the desired brightness.
Major elevation adjustment should not be needed but, if necessary, it should be
accomplished by shimming the mount base. It is important not to use the eleva-
tion adjustment of the scope for major adjustments. Your scope's internal eleva-
tion adjustment should be reserved for fine tuning to achieve zero at the called for
distance.
5
oBjectIVe tRIm RIng
5
BodY tuBe
5
4/3/06 3:48:26 PM
3