KIKKA BOO RONDA Instrucciones De Uso página 13

2.3. The equipped position of the restraint in a vehicle. This child safety seat is available with a three-point seat belt that passes through the GB14166 or
ECE R 16. Not suitable for models with only 2-point seat belts.
Note: it is recommended that the ISOFIX chuck of the seat be locked on the ISOFIX connector of the car when installing the child seat.
2.4. THE HEADREST HEIGHT ADJUSTED METHOD
Depending to the height of the child, the headrest can be adjusted in 11 positions. As shown, adjust the red handle to the appropriate height by
adjusting the handle up and down at the same time.
Important: after releasing the headrest by adjusting the lever, check that the headrest is locked in a safe and suitable position by pulling up or down the
head.
2.5. THE SHOULDER STRAPS ADJUSTED METHOD
Check that the shoulder strap height is suitable for your child: straps should pass through straps that are equal to the child' s shoulder or slightly higher
than the child's shoulder position (the correct seat belt position is shown in the gure).
The height of the shoulder strap of this product can be adjusted up and down with the up and down of the headrest. When using, adjust the height of
the headrest to adjust the suitable shoulder strap height.
2.6. THE BUCKLE USED METHOD
2.6. Pull the button left and right together.
2.7. Insert the closed insert into the slot at the same time. If you hear the H clickn sound, it means that the buckle is stuck. Pull the insert up and check
that the buckle is locked properly.
2.8. To unfasten the seat belt, press the red button down and the insert will pop up automatically.
THE LENGTH OF THE SHOULDER STRAPS ADJUSTED METHOD
2.9. Tighten the straps:
Pull the straps outward until the straps are completely tightened. Tighten the straps as much as possible without causing discomfort to the
child. The leg seat belt is as low as possible and should be located near the crotch rather than the abdomen. Loose straps are dangerous. So
every time the child is placed in the child' s seat, check that the seat belt adjuster can be used normally, and then pull the 5 straps, tighten
the straps, and do not twist the straps.
2.10. Loosen the straps:
The shoulder strap can be loosened by pressing the seat belt adjuster (hidden under the cover of the seat).
Action: press the seatbelt regulator down while the other hand holds two straps to the front of the child to loosen the straps.
2.11.THE ISOFIX ADJUSTED METHOD
As shown press the red ISOFIX release button and push the FIT chuck out to the outermost so that the ISOFIX chuck can be installed.
If you want to retract the ISOFIX chuck, you can pull the ISOFIX chuck back by pressing the red ISOFIX release button inward.
2.12. ISOFIX INSTALLATION
Step 1: First pull the ISOFIX chuck to the outermost end, then insert the ISOFIX interface on the car. When you hear "click" to indicate that the
ISOFIX chuck and the ISOFIX interface are fully docked, note: at this time, the FIT lock display window appears green.
Step 2: Push the seat against the back of the car until the two are perfectly tightly aligned. If you want to release the ISOFIX chuck, you can
unlock the ISOFIX chuck by pressing the red release button of the FIT chuck.
Step 3: Use a 3-point safety belt to install the child safety seat for speci c actions.
2.13. Use status of child safety seat support legs
Group 0+ uses support legs as shown in Figure 1,Group 1 uses support legs as shown in Figure 2. Press the support leg to adjust.
Press the support leg adjustment button in one hand and push the base support leg up in the other hand to hear the "click" back of the
support leg.
2.14. Angle adjustment and rotation adjustment of child safety seat
As show in gure 1, the seat angle can be adjusted by pressing the red angle adjusting lever. It is convenient to adjust the suitable angle and
increase comfort when using. Pull the red adjusting lever to adjust the seat angle. ttention : This seat has Five reclined positions.
Position 1 (the most inclined position) for Group 0+/1, rearward facing installation.
Position 2,3,4 for group 1, forward facing installation.
Position 5(the most upright position) for Group 2/3, forward facing installation.
ENGLISH