Action Activejet Selected WSS-100BPL Manual De Instrucciones Y Condiciones De Garantía página 7

GB
Stand fan Activejet Selected WSS-100BPL
Modern stand fan Activejet WSS-100BPL will effectively set large masses of air in motion, providing an instant feeling of cooling on hot days. It is easy to
use, extremely quiet and takes up little space. It has an advanced speed control system with a touch panel, remote control. The fan also has an oscillation
function and the adjustable angle, so the produced airflow can reach all parts of the room. It is designed for use in residential, commercial and office spaces.
Features:
• A large propeller with seven blades.
• Extremely quiet DC motor.
• 18 rotation speeds / 3 modes of operation.
• 10-hour Timer.
• Touch control panel with LED display.
• Remote control.
• Oscillation function - horizontal movement in the range of 80 degrees (with possibility of switching off).
• Vertical angle adjustment of the head within 20 degrees.
• The telescopic height adjustment allows for smooth lifting and lowering of the fan.
• The stable base with internal ballast prevents the device from accidentally tipping over.
• Unique and elegant look.
• Easy to assembly. You can disassemble the fan after the season.
NOTE:
Before using the fan, read the Instruction Manual. We recommend that you keep this manual for future reference.
While the fan is in operation, it is advisable to follow the basic safety rules to avoid a fire, electric shock and mechanical damage to the body.
Observing the instructions and recommendations contained in the Instruction Manual extends the device's service life.
SAFETY RULES:
1. Do not attempt to repair the device yourself.
2. Keep the device work area in order.
3. Keep the device away from moisture and water, explosive and flammable substances and particles. Failure to follow these rules may result in a fire
or electric shock. Excessive dusting of the device may lead to overheating of the motor and permanent damage to the fan.
4. It is forbidden to use wires with the plug that is not original or any adapters.
5. Take care of the power cord. Do not use the cord to move the device, pull it or pull the plug from the power outlet. Protect the cable from heat,
mechanical damage, oil.
6. Do not put your fingers or devices in the air outlet/inlet grille. Take care that long hair is not screwed into the propeller of the device in use.
7. The device is not intended for people with limited physical, sensory or mental abilities. Children under the age of 8 and people with restrictions may
use the device only under the supervision of a person responsible for their safety.
8. Do not cover the device e.g. with clothes, do not use it for drying wet clothes, etc.
9. Make sure that the power supply complies with the voltage specified for the device (220-240V ~ / 50-60 Hz).
10. Installation, disassembly, cleaning and maintenance of the fan may take place only after removing the plug from the socket.
11. Do not leave the switched on device unattended.
12. The device is intended for use indoors, in clean and dust free rooms. The fan should be placed on a hard, flat surface at a distance of 0.3–1 m from all
objects, such as radiators, other electrical appliances, furniture, and curtains.
TECHNICAL DATA:
Model: WSS-100BPL
Voltage and frequency: AC 220–240 V, 50–60 Hz
Power consumption: 32W
Propeller diameter: 36 cm
Height: 77 – 100 cm (adjustable)
Weight: ~6,5 kg
Colour: white
ASSEMBLY:
1. Start the assembly by assembling the fan base. Place the tripod with the lower, thicker tube
in the base hole and attach a large safety nut on the underside. Tighten the nut firmly clockwise.
2. The base assembled in this way place on a hard, stable base.
3. Put the rear propeller cover (8) on the engine, lock the large nut (14) (clockwise).
4. Place the fan propeller (2) on the engine shaft and secure with the nut (15) (NOTE - counterclockwise).
14
5. Replace the propeller front cover (6) and the outer ring of the cover (7), with the connector (16). Place the cap (1) in the front opening of the cover.
14
CONNECTION TO THE NETWORK:
Ensure that the mains supply at your location matches the voltage shown on the nameplate of the device. If the mains plug of the device has a protective
earth contact, use only electrical outlets that also have a protective earth contact, i.e. a so-called earth pin.
USE:
Make sure that the fan is placed on a flat and level surface away from other heat sources, at a sufficient distance from curtains and other lightweight
materials that the air rush could pull into the fan.
1. On / Off. When the power is turned on, the ON / OFF button „
willstart in „normal" mode with 18 speeds. At the same time, the „+" and „-" sensors are activated (illuminated). They allow to set the desired fan
speed 1 - 18. Pressing „ „ again will switch off the fan.
2. Timer. Temporary shutdown function. With the fan on, press the „
The time after which the fan is to be switched off is set with „+" and „-" sensors. Setting range from 1 to 10 hours.
3. Timer. Temporary switch-on function. With the fan off (standby mode) press the „
light up. The time after which the fan is to be switched on is set with „+" and „-" sensors. Setting range from 1 to 10 hours.
Wind mode. Pressing the „
4. „ button again will activate the „Natural" mode, which simulates a variable wind speed through a variable, random
speed. The corresponding „Natural wind" mode light will light up. By pressing the „+" or „-" button, you can change the blowing force in natural mode
to „mild wind". (display shows F1), „medium wind" (F2), „strong wind" (F3) or „silent wind" (display shows F4).
5. Sleep mode. The next, third press of the „ „ button activates the „Sleep" mode, where the speed of blowing changes very smoothly and gently
within a certain range, acting as a calming and finally asleep. The corresponding „Sleep Mode" light will light up. The „+" or „-" button can be used to
change the blowing force „very mild soporific wind". (the display shows P1), „mild soporific wind" (P2), ‚medium soporific wind (P3) or‚ quiet soporific
wind' . (display shows P4).
Pressing „ „ again will return to timer mode.
The sequence for changing the operating mode is as follows: „Timer → Natural mode → Sleep mode".
6. Oscillation function. To turn on the oscillation, after turning on the power, press the „
7. Automatic switching off the display. After the setting is completed, if no operation is performed for 1 minute, all the indicators will go out
and only the „Power" check box will be left (the red light flashes every 15 seconds). The display is activated by pressing any key.
8. Automatic switching off. The fan will automatically switch off after 12 hours if there are no commands from the control panel or remote control.
Remote control. The buttons on the remote control correspond to the main functions of the fan housing.
9.
10. The fan has a memory function, but all settings will be reset when disconnected from the mains.
11. Height adjustment. To set the desired fan height, press the button in the center of the tripod, slide out or slide in the top of the column and release
the button.
Stand fan Activejet Selected WSS-100BPL
8
2
6
15
16
„ will light up red. To start the fan for the first time, press this button once. The fan
„ button once. The corresponding light under the button will light up.
„ button once. The corresponding light under the button will
„ button. Press this button again to disable the function.
15
GB
7
1