ANSMANN WL 200R Manual De Operación página 4

SCOPE OF DELIVERY
ƒ ƒ
WL200R Workshop lamp
ƒ ƒ
USB power supply 5V/500mA
ƒ ƒ USB/Micro-USB charging cable 150cm
ƒ ƒ Manual
FUNCTIONAL OVERVIEW
ƒ ƒ
Professional workshop lamp with the latest SMD LED technology
ƒ ƒ
Robust plastic housing with rubber-coated grip
ƒ ƒ
Can be swivelled through 340°, lamp grip can be locked in twelve positions for flexible
direction of the light
ƒ ƒ Fastening magnet on the bottom of the grip
ƒ ƒ Fold-out hook on the top of the housing can be swivelled through 360°
ƒ ƒ Integrated belt clip on the rear of the housing
ƒ ƒ Light with two light functions (100% / 50% light power)
ƒ ƒ
Permanently installed Li-ion rechargeable battery pack (3.7V / 1550mAh)
ƒ ƒ
Charging possibility via USB mains adapter (110V-240V) or USB car adapter (12-24V)
ƒ ƒ
Charge monitoring via coloured LED on the rear side of the lamp
TECHNICAL DATA
Integrated illuminants:
3.25W
Lighting intensity:
Luminous flux:
Battery life:
Input voltage for the external mains adapter:
Charge time:
USE
The on/off switch for the workshop light can be found on the top of the housing:
ƒ ƒ Press 1x: The WL200R workshop lamp will be switched on in 100% light mode.
ƒ ƒ Press 2x: The workshop lamp illuminates at the 50% setting.
ƒ ƒ Press 3x: The lamp is switched off.
CHARGING PROCEDURE
Charge the workshop lamp fully before using for the first time. If the workshop lamp has been
stored for an extended period of time it should likewise be fully charged again before first
use.
The following charging options are available:
ƒ ƒ
Via USB mains adapter plugged into the mains outlet
ƒ ƒ Via USB car adapter connected to the cigarette lighter of the vehicle
ƒ ƒ Via USB cable connected to a third party device with a USB output port (e.g. PC, laptop)
To charge the WL200R workshop light, pull the sealing cap off the micro-USB socket on the
rear of the lamp. Connect the USB mains adapter / USB vehicle adapter with the WL200R
workshop lamp by plugging the micro-USB plug on one end of the USB / micro-USB charge
cable provided into the micro-USB socket on the light and plugging the USB plug on the other
end of the charge cable into the USB socket of the USB mains adapter / USB vehicle adapter.
Then plug the USB mains adapter into a mains outlet or plug the USB vehicle adapter into the
cigarette lighter of the vehicle. To charge the workshop light with a third party device, plug
the USB plug on the charge cable into the USB socket of the third party device after having
first connected the micro-USB plug on the other end of the charge cable with the workshop
lamp as described above.
CHARGE STATUS INDICATION
The WL200R workshop lamp has a professional LED status indicator on the rear of the lamp
(besides the charging socket). The LED illuminates red during the charge procedure and
illuminates green once the battery pack is fully charged.
The WL200R workshop lamp is protected against over-charging. This means that you can
leave the workshop lamp connected to the charging power after its rechargeable battery
pack has been fully charged.
English
Deutsch | | Français | Pусский | Español | Svenska | Italiano | Nederlands
main light 5x SMD LEDs, Nominal power
400 Lux at 0,5m distance
220 Lumen
ca. 3.5h (100% light power)
ca. 10h (50% light power)
100-240V AC / 50-60Hz
ca. 4,5h