Ubbink Niagara Acrylic 30 LED Instrucciones De Uso página 5

1 Operating instruction for stainless steel waterfall ornaments Niagara 30 / 60 / 90 - 30 LED / 60 LED / 90 LED
1 Operating instruction for stainless steel waterfall ornaments Niagara/Nevada 30/60/90 - 30 LED/60 LED/90 LED
Operating instruction for stainless steel waterfall ornaments Niagara Acrylic Operating instructions for Waterfall NIAGARA Acrylic
An unusual design waterfall for swimming pools made from chlorine and salt water-resistant acrylic glass with an integrated 12V LED illumination.With these Instructions for
use, you receive important information which is helpful for the installation, commissioning, maintenance and care of your acrylic waterfall. Please read these Instructions for
use carefully and store them safely.
Technical data
Modell
Article number
Material
Hose connection
Recommended pump output
Pools with sand filter
(0.8 bar = 8 mWs)
LED illumination
LED strip
Voltage/frequency
Safety transformer
Power consumption
Cable length LED lamps
Level of protection
Protection class
Scope of delivery
Wall mounting
Screws
Safety transformer
Also required
T-piece 1 1/2 "
Ball valve 1 1/2"
Hose connector 1 1/2" x 38mm
Hose clamp 25-40mm
Hose 38 mm
Additionally required connection material (not included within the scope of the delivery)
- 1 T-piece 1 1/2" (3 x inner thread)
- Pool hose 38 mm (of the required length)
Safety instructions for Niagara/Nevada 30 LED / 60 LED / 90 LED
Use
The NIAGARA LED Acrylic waterfalls are exclusively intended for installation and operation in swimming pools for private households.
Installation
1.) Installation into a wooden cube
• Position and attach the wooden cube to the wooden pool edge of your swimming pool.
• Ensure that the hose connection for the waterfall element can be easily connected to the existing water return from the filter around the pool.
• Prepare the waterfall element for connection to the existing water return system.
• Subsequently, using the enclosed wall attachment, you can securely mount the waterfall element to the rear side of the wooden cube and undertake the hose connection.
• Check the LED strip is correctly positioned, lay the lamp cable outside the swimming pool and connect it using the safety transformer.
• Check the complete water cycle once again for leaks. Non-sealed screw or hose connectors should be sealed using conventional Teflon tape.
• Prior to commissioning the waterfall, regulate the water flow as follows:
Ball valve
Waterfall ornament
Water return pool
• Now you can switch on the pump and LED illumination and put your waterfall into operation.
• Should the water discharge at the waterfall element be too great, then this can be regulated and adjusted accordingly using the ball valve.
2.)Other installation forms
Installation is possible into other constructions and on a pool edge made from other material (e.g. plastic, concrete). The attachment material required for this purpose is not included
within the scope of delivery.
Niagara 30 LED - Acrylic
7504608
Acrylic
1 1/2" (inner thread)
4,5 - 11 m3/h
Poolmax TP 50 / 75 / 120
Strip 30 cm, 20 LED, cold white
12 VAC 50 Hz
TDC DE 3.25-12 W
max. 3 W
5 m
III
IP68
2
4
1
1
1
4
4
Of the required length
-1 Ball valve 1 1/2" (1 x inner thread/1 x outer thread)
- 4 Hose clamps 25-40mm
Waterfall ON
Open (ON)
Closed (OFF)
Niagara 60 LED - Acrylic
7504609
Acrylic
1 1/2" (inner thread)
4,5 - 11 m3/h
Poolmax TP 50 / 75 / 120
Strip 60 cm, 35 LED, cold white
12 VAC 50 Hz
TDC DE 10.5-12 W
max. 4,0 W
5 m
III
IP68
2
4
1
1
1
4
4
Of the required length
- 4 Hose connectors 1 1/2" x 38mm
Waterfall OFF
Closed (OFF)
Open (ON)