Emerson insinkerator TranScape View HC-View-SS Instalacion, Cuidado & Uso página 4

2
INSTALLING THE FAUCET - VIEW/ WAVE
A
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
B
1
5 ⁄ " Small
8
Steel Washer
1 5 ⁄ " Small
8
1 5 ⁄ " Small
8
Rubber Washer
Steel Washer
1 5 ⁄ " Small
8
Rubber Washer 2 1 ⁄ " Large
4
Steel Washer
1
Standard 1 ⁄ " hole Hole larger than 1
2
Faucet is factory-ready for installation
into a standard 1 1 ⁄ " sink/counter hole.
2
C
Hot & Cool models only
Star Nut
Fiber
Washer
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
1
5 ⁄ " Small
8
Steel Washer
Fiber
Washer
1
5 ⁄ " Rubber
8
Washer
Figure 1 Figure 2
If sink/counter thickness exceeds 3/4"
a hole diameter of 1 1 ⁄ " is required.
2
6
View/Wave
I I
Unpack dispenser components.
I I
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
View/Wave
For a standard 1 1 " sink/counter hole
⁄
2
I I
Feed tubes down through the hole in
the sink/counter until the base is at
rest. Set faucet at desired angle.
Large washer required for sink holes larger
than 1 1 " or for porcelain sinks with radius
⁄
2
or beveled holes.
I I
1 ⁄ " Before feeding tubes through sink
2
hole, remove extension. Place 2
large steel washer over threads on
faucet base. Reinstall extension.
View/Wave
I I
From under sink, slide 2 1 ⁄ " fiber washer
4
over threaded extension. Thread star
nut onto extension until snug.
Hot & Cool models only
I I
Attach the quick connector to the ends
of the copper tubes running from the
dispenser.
I I
Install a white 3/8" tube into other end
of quick connector.
Installing into hole smaller than 1
I I
Unscrew and remove threaded extension
from valve body. Do not discard, as you
will need this later (See Figure 1).
I I
Leave small washers in place.
Star Nut
I I
Feed tubes down through the hole in
the sink/counter until the base is at
rest. Set faucet at desired angle.
I I
⁄
From under sink, slide 2 1 " fiber washer
4
over faucet base. Reinstall threaded
extension onto the base until snug.
Thread star nut onto extension until
snug (See Figure 2).
2
INSTALLING THE FAUCET - H990
A
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
B
1
⁄ "
4
Make sure to use rubber gasket
C
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
1 ⁄ "
2
H990
I I
Unpack dispenser components.
I I
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
H990
I I
Ensure that the black rubber gasket
is properly seated into the base of
the dispenser head and will
surround the sink mount.
I I
Feed tubes down the hole in the
sink or countertop until the base is
at rest on the sink or countertop
surface.
to ensure proper seal.
H990
I I
From under the sink, place the
semi-circular mounting plate onto the
threaded stud.
I I
Place wing nut onto the threaded
stud. Make sure faucet head is at the
desired angle. Tighten the wing nut
until snug, while ensuring the semi-
circular mounting plate extends
beyond the sink hole.
7