Operating Tips - SNOWJOE 24V-X2-SB18 Manual Del Operador

Quitanieve inalámbrico
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3. While depressing the safety switch button, pull the
ON/OFF trigger toward you. Once the machine powers on,
release the safety switch button and begin operation
(Fig. 16). The machine can only be started by depressing
the safety switch button first, followed by squeezing
the ON/OFF trigger; reverse operation will not start the
machine.
Fig. 16
Safety switch button
4. To power off, release your grip on the ON/OFF trigger.

Operating Tips

m
WARNING!
Foreign objects, such as rocks, broken
glass, nails, wire, or string, can be picked up and thrown by
the snow blower, causing serious personal injury. Remove all
foreign objects from the area to be plowed before operating
the snow blower.
1. Keep the area of operation free of foreign objects that can
become thrown by the rotor blades. Perform a thorough
inspection of the area since some objects may be hidden
from view by surrounding snow. If the snow blower hits
an obstruction or picks up a foreign object during use,
stop the snow blower, remove the batteries, remove the
obstruction, and inspect the unit for damage. Repair or
replace any damaged part before restarting and operating
the unit.
2. Keep children, pets, and bystanders away from the area of
operation. Be aware that the normal noise of the machine
when turned on may make it difficult for you to hear
approaching people.
3. When moving the snow blower, use the wheels on one
side as the pivot point. Slightly tilt the snow blower on this
pivot point to move it forward or backward.
4. Start your clearing path outward, throwing snow in a back
and forth motion. To clear in the opposite direction,
pivot the snow blower on its wheels. Make sure to overlap
clearing paths.
5. Note the wind direction. If possible, move in the same
direction as the wind so that the snow is not thrown
against the wind (and thus back into your face and on the
just cleared path).
6. Do not push the snow blower with excessive force.
You should push the machine gently and evenly in
accordance with the unit's throw rate.
ON/OFF trigger
12
7. Do not apply additional man-made load to the motor since
this may cause motor damage.
8. Some parts of the snow blower may freeze under extreme
temperature conditions. Do not attempt to operate the
snow blower with frozen parts. If the parts freeze while
the snow blower is in use, stop the snow blower, remove
the batteries, and inspect for frozen parts. Free all parts
before restarting or operating the snow blower.
Never force controls that have frozen.
9. When working on pebbles, gravel, or unpaved surfaces,
avoid throwing loose surface material along with the snow
by pushing down on the handle to raise the scraper at the
base of the unit above the pebbles or gravel.
Headlight
The snow thrower is equipped with a headlight that can be
used to illuminate the forward path in the dark. To use the light,
turn on the light switch located on the back side next to the
battery compartment on the left (Fig. 17).
Fig. 17
NOTE: The lights will only turn ON when the snow thrower
is running. After finishing your work session, REMEMBER to
TURN OFF the light switch.
Changing Throw Direction and
Throw Height
m
WARNING
Never direct the snow discharge chute at the
operator, at bystanders, at vehicles, or at nearby
windows. The discharged snow and foreign objects
accidentally picked up by the snow thrower can
cause serious damage and personal injury.
Always orient the discharge chute in the opposite
direction from where you, bystanders, surrounding
vehicles, or windows are located.
1. The discharge chute can be adjusted 180 degrees by
rotating the chute crank. Rotate the chute control crank
clockwise to move the discharge chute to the left and
counterclockwise to move the chute to the right (Fig. 18).
Light switch
m

Publicidad

Tabla de contenido
loading

Tabla de contenido