Lutron HWBP-2S-15-120L3 Instrucciones De Instalación

Installation Instructions
Please Read Before Installing
Table 1 - Models and Ratings
Voltage/
Model
Frequency
HWBP-2S-15-120L3
HWAP-8D-15-120L3
HWBP-8D-15-120L3
120 / 240 V~
50/60 Hz
HWBP-2S-20-120L3
HWAP-8D-20-120L3
HWBP-8D-20-120L3
HWBP-2S-15-120L4
HWAP-8D-15-120L4
HWBP-8D-15-120L4
120 / 208 V~
50/60 Hz
HWBP-2S-20-120L4
HWAP-8D-20-120L4
HWBP-8D-20-120L4
Breaker panels are required to be installed to provide sufficient access
and working space according to the National Electrical Code
Depending on the conditions, a typical installation may require 3 ft to
4 ft (0.914 m to 1.22 m) in front of the panel and 30 in (762 mm) width
to provide sufficient space for panel access. Please consult your local
electrical inspector for all NEC
requirements may include: maximum and minimum breaker height above
the floor, proximity to distribution panel, room size, and room entrance
specifications.
Important Notes
Codes: All wiring must be installed in accordance with all local and national
electrical codes.
Cooling: This equipment is air-cooled. Mount in a place where the vented
cover will not be blocked. Clearance of 12 in (304 mm) is required in front of
the unit.
Environment: Indoor use only.
Mounting Location: Modules will hum slightly and internal relays will click
while in use. Mount in a location where such noise is acceptable. Mount
panel so that line voltage wiring will be at least 6 ft (1.8 m) from audio or
electronic equipment wiring.
Installation
1. Mount the Panel (Figure 2 / Table 2). Use one of the methods below.
Mounting hardware not pro vid ed.
a. Surface Mount - Use keyholes with bolts (1/4 in [M6] recommended).
b. Recess Mount - Use screws at the corners of the panel. Mount panel
flush or less than 1/8 in (3 mm) below the finished wall surface. When
recess mounting in a 2 x 4 stud bay, the drywall must be built out or a
frame must be constructed to accommodate the panel depth.
Table 2 - Mounting Specifications
Minimum Hardware
Model
Load
HWBP-2S-15-120L3
HWBP-2S-20-120L3
30 lb (14 kg)
HWBP-2S-15-120L4
HWBP-2S-20-120L4
HWAP-8D-15-120L3
HWBP-8D-15-120L3
HWAP-8D-20-120L3
HWBP-8D-20-120L3
100 lb (45 kg)
HWAP-8D-15-120L4
HWBP-8D-15-120L4
HWAP-8D-20-120L4
HWBP-8D-20-120L4
P/N 043517 Rev. A
07/2019
Input
Feed
Maximum
1 phase,
175 A
3-wire
3 phase,
175 A
4-wire
and local requirements. Other possible
®
Depth Cover Dimensions
24.5 in x 15.875 in
3.875 in (98 mm)
(622 mm x 403 mm)
59.5 in x 15.875 in
4.125 in (105 mm)
(1511 mm x 403 mm)
Rough-In Panel With Breakers
HWBP-2S-15-120L3, HWAP-8D-15-120L3, HWBP-8D-15-120L3
HWBP-2S-20-120L3, HWAP-8D-20-120L3, HWBP-8D-20-120L3
HWBP-2S-15-120L4, HWAP-8D-15-120L4, HWBP-8D-15-120L4
HWBP-2S-20-120L4, HWAP-8D-20-120L4, HWBP-8D-20-120L4
Figure 1 - Dimensions
Dimensions shown as: in (mm)
Breaker
2
Capacity
(52)
15 A
2.4
(61)
20 A
15 A
20 A
41.8
(1062)
(NEC ).
® ®
14.8
(376)
Figure 2 - Wiring and Mounting
Main
Feed
Entry
8
(203)
0.313
(8)
diameter
0.625
(16)
diameter
59
(1500)
11
(280)
Mount
Vertically
14.4
(366)
15
(381)
Load Wiring Entry
Recess-Mount
(4 screws)
Surface-Mount
(4 keyholes)
Terminal Blocks
Main
Feed
Entry
MI
Mounting
Screws
Ground
Lug
English
15
(381)
8
(203)
1
(25)
21.5
24
(546)
(610)
1
(25)
10.75
(273)
1
(25)
UP
Panel
MI
Mounting
Screws
Ground
Lug
Control Wiring Entry
(IEC PELV/NEC Class 2)
®