Operation; Filling The Tank - Hoover BH90100 Manual Del Usuario

OPERATION

WARNING:
Do not allow familiarity with the product to make you careless.
Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields or goggles marked to
comply with ANSI Z87.1. Failure to do so could result in fluids entering your eyes
resulting in possible serious injury.
WARNING:
Use safety equipment. Protect your eyes, skin, and lungs while
mixing, filling, spraying, and cleaning. Failure to do so may result in serious personal
injury and damage to property.
NOTICE: Before each use, inspect the entire product for damaged, missing, or loose parts
such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are replaced. Please contact
customer service or an authorized service center for assistance.
What Solution Can You Use?
You may use this product for the purpose listed below:
• For use with most consumer grade cleaning solutions.
DO NOT USE THIS SPRAYER WITH BLEACH, HYDROGEN PEROXIDE, PINE SOL OR PINE
OIL BASED SOLUTIONS. DO NOT USE WITH VINEGAR.
• For use with most consumer grade home and garden chemicals such as
insecticides, fungicides, weed killers and fertilizers.
WARNING:
If this product is used for herbicide/insecticide applications do not
re-purpose it for use with disinfectants. Obtain a second nozzle set and tool for
dedicated use with disinfectants only. Tools used for herbicide/insecticide applications
are regulated under EPA Federal Insecticide, Fungicide, and Rodenticide Act regulations
and are considered contaminated.

Filling the Tank

When adding spray solutions, you may add water and the desired chemical solution directly
into the tank, or use a solution that has been premixed in a separate container, then poured
into the sprayer, using a funnel if needed. For either method, remember:
• Liquids used must be as thin as water. Thicker liquids will not spray properly.
• Do not overfill the tank.
NOTE: If using a measuring container or funnel to fill the tank, be sure to thoroughly
clean and rinse these items after use. If premixing the spraying solution, rinse the
container used for mixing.
TO FILL:
1. Remove the battery pack.
2. Unlock the latches securing the tank to the sprayer.
3. Tilt the base of the tank away from the sprayer and then remove it.
4. Unscrew the cap and remove it from the tank.
5. Fill the tank with the desired amount of liquid (up to 16 oz or 500mL).
NOTE: To ensure proper operation of the sprayer, do not fill past the max fill line.
6. Screw the cap back onto the tank, making sure it is tightened securely.
NOTE: Wipe the outside of the tank with a dry cloth and clean up any spills before
inserting the tank.
7. Insert the tank into the sprayer at an angle.
8. Push the base of the tank into the groove at the base of the sprayer until it clicks into
place.
9. Lock the latches to secure the tank in place.
10. Reinstall the battery pack.
NOTICE: It is important to thoroughly clean the unit after each use. Allowing liquid to
remain in an idle tool for an extended period may cause its moving pieces and connectors
to seize up.
4
Filling the Tank (Continued)
B
A
A. 16 oz. Tank
B. Latch
Connecting the Battery Pack
WARNING:
Always remove battery pack from your tool when you are
assembling parts, making adjustments, cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could cause serious personal injury.
TO INSTALL OR REMOVE:
1. Insert the battery pack into the product.
2. Make sure the latches on each side of the battery pack snap in place and the battery
pack is secured before beginning operation.
3. Depress the latches to remove the battery pack.
NOTE: For complete charging instructions, see the operator's manuals for your battery
pack and charger.
A. Depress latches to release battery pack
B. Battery Pack
A
B
A. Cap
B. 16 oz. Tank
B
A