3M PPS 2.0 Serie Manual Del Usuario página 5

"pressure relief valve" located in the base of the cup to avoid over pressurizing. If the pressure
relief valve is damaged, the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup must be replaced.
• Use Only Genuine 3M Parts and Accessories. Reference Figure 2 Component Listing. Setup
Sequence:
1. Insert a PPS 2.0 liner into the PPS series 2.0 H/O pressure cup and add the desired amount of material to be
sprayed.
2. Select the appropriate PPS 2.0 lid, carefully remove the black collar from the lid, insert the lid into the liner
and press down until secure.
3. Align the opening on the Retaining Collar Shroud Assembly (6) with the 3M™ PPS™ Series 2.0 H/O Lid and
screw the Retaining Collar clockwise onto the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup (1) and hand-
tighten.
4. If the material will not be sprayed immediately, a 3M™ PPS™ Series 2.0 Plug (7) can be inserted into the
lid spout to seal contents.
5. When ready to spray the contents, remove 3M™ PPS™ Series 2.0 Plug (7) if used, and connect the spray
gun with the previously installed 3M™ PPS™ Series 2.0 Adapter to the 3M™ PPS™ Series 2.0 Type H/O
Pressure Cup. Reference Figure 1.
a. While aligning the 3M™ PPS™ Series 2.0 Adapter with the 3M™ PPS™ Series 2.0 H/O Lid and the
3M™ PPS™ Series 2.0 Retaining Collar Shroud Assembly, press down to fully seat and then turn gun
1/4 turn clockwise, ensuring all 4 connection points engage.
6. Attach the cup pressure hose (2) from the spray gun to the pressure port (1b) on the 3M™ PPS™ Series
2.0 Type H/O Pressure Cup. The hose clip on the cup (1a) may be used to hold the hose securely in place
while spraying, hose clip included in 3M™ PPS™ Series 2.0 Type H/O Pressure Cup (Large) only.
7. Connect the spray gun to the air supply.
8. With the spray gun and the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup held perpendicular to the
ground, pull the trigger and adjust to the desired cup pressure, not to exceed a maximum operating
pressure of 10 psi (69 kPa, 0.69 Bar). Caution: Pressure relief valve (1c) at the base of the cup will
open at 30 psi (207 kPa, 2.07 Bar) and relieve excess pressure. The relief valve will close and
reset when the cup pressure is reduced. Keep trigger pulled until air from inside the 3M™ PPS™ Lid
and Liner has been totally evacuated and a steady spray of material is coming from the spray-head of
the gun. This will allow the gun to be held and sprayed upside down without fluid interruption.
9. Spray materials normally, periodically check the pressure to the cup to ensure pressure does not exceed
maximum operating pressure.
10. When done spraying, disconnect the input air supply from the spray gun.
11. Attention: Before disassembling the gun from the cup, the pressure must be relieved by
disconnecting the cup pressure hose at the base of the cup (1b).
12. While holding the spray gun upright for a bottom fed spray gun or turning the spray gun gun over for a
gravity fed spray gun. Pull the trigger to allow any remaining material to drain out of the fluid passage in
the spray gun and 3M™ PPS™ Series 2.0 Adapter back into the 3M™ PPS™ Liner:
Attention:Failure to do so will result in a material spill on the 3M™ PPS™ Series 2.0 Retaining Collar
Shroud Assembly.
13. Disconnect the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup from the spray gun at the 3M™ PPS™
Series 2.0 Adapter by turning the gun counter-clockwise slightly to disengage locking tabs and pull gun
upwards to separate from the cup assembly.
14. Clean the gun and adapter with appropriate materials and store appropriately.
15. Unscrew the 3M™ PPS™ Series 2.0 Retaining Collar Shroud Assembly (6) by turning the ring counter-
clockwise and remove it from the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup (1).
16. Remove the 3M™ PPS™ Series 2.0 Lid (5) and Liner (4) and dispose of properly referring to the material
SDS and consulting local regulations.
17. Clean the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup (1) and 3M™ PPS™ Series 2.0 Retaining
Collar Shroud Assembly (6) by wiping with solvent and a lint free towel. Store in a clean, dry area.
Caution: Do not soak in solvent.
English - 3