Setup Instructions; Preventative Maintenance - K Tool International KTI61002 Manual Del Propietário

SETUP INSTRUCTIONS

This is the safety alert symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
Refer to parts breakdown on page 5:
1. Attach legs (#12) to connecting plate (#9) using hex bolts (#8), washers (#10) and nuts (#11). Do not tighten the hardware.
2. Attach the small braces (#22) to the positioning plate (#23) using the hex bolts (#8), washers (#10) and nuts (#11). Do not tighten.
Attach the other ends of the small braces (#22) to the legs (#12) using the bolts (#15), washers (#14) and nuts (#13). Do not tighten.
3. Attach the middle braces (#24) to the legs (#12) using the bolts (#16) and lock washers provided. Do not tighten.
4. Repeat step 3 but with the long braces (#25). Tighten all hardware mentioned in steps 1 through 4.
5. Insert the extension screw (#4) through the bottom opening of the post (#7) and turn the post at a downward angle so the screw
extends out the top of the post.
6. Fit the bearing assembly (#6) over the screw (#4) and then thread the adjusting handle (#5) onto the screw (#4).
7. Secure the saddle base (#3) to the top of the screw (#4) with the locking bolt (#17). Secure the saddle pad assy (#2) to the saddle
base (#3) with the four bolts (#1).
8. Insert the entire post assembly through the top of the connecting plate (#9) and the positioning plate (#23). Secure the post
assembly to the tripod stand using the pin (#19) and R pin (#18). Insert the pin (#19) through the hole in the connecting plate (#9)
and any corresponding hole in the post (#7). Make sure the pin goes through both sides of the connecting plate (#9) and the post
(#7) before securing the pin (#19) with the R pin (#18).
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Make sure the vehicle is properly supported, stable and at the required work height before positioning the stand(s) under the
vehicle component to be supported.
2. Consult the lift and vehicle manufacturer for the proper positioning of the under hoist stands.
3. Once the stand(s) has been positioned properly under the vehicle, hold the stand's saddle in place with one hand while turning the
spin handle in a clockwise direction with the other hand. Remove the one hand from the stand's saddle when it comes close to
making contact with the vehicle.
4. Continue turning the stand's spin handle in a clockwise direction until it applies light pressure against the component. This
pressure should not exceed what is required to support the vehicle. Excessive pressure might cause the vehicle or its component
to become unstable.
5. Before removing the stand from the vehicle, make sure the vehicle is still properly positioned on the lift. Removal of the stand can
be accomplished by turning the spin handle in a counterclockwise direction until the stand's saddle is clear of the vehicle.

PREVENTATIVE MAINTENANCE

This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to
potential personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the stand in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust,
or any other harmful elements. The stand must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. Use a general purpose grease to lubricate the extension screw.
3. Every stand owner is responsible for keeping the stand labels clean and readable. Use a mild soap solution to wash external
surfaces of the stand. If product labels are lost or not legible, contact an authorized K-Tool International repair center for
replacements.
4. Inspect the stands before each use. Do not use the stands if any component is cracked, broken or bent. Do not use the stand if
it has loose or missing hardware or components, or is modified in any way. Take corrective action before using the stand again.
Premature wearing or damage to components caused by loose or missing hardware is not eligible for warranty consideration.
KTI61002 3 7/2/14